I agree, Carl, those values don't sound quite right. They were marked
in pencil on the back of the cap, but I don't know how they got there.
I'll do an accurate measurement today and update the values.
The cap came out of a 3-tube 230CA. It has the inexpensive wiper, but
so far as I know that was never a problem. I'm going by memory, but I
believe the same wiper was used on the L4B tune cap. As Jim noted,
it's probably best to upgrade the wiper for the load cap.
73,
Jim w8zr
Sent from my iPhone
> On Jun 24, 2014, at 4:00 AM, Carl <km1h@jeremy.mv.com> wrote:
>
> As with all OEP 73 series caps there are 3 different current handling
> versions; the cheapest is not the best and the highest isnt necessary.
>
> I have the original Alpha built by Cardwell 154-10-53 cap here, as used in
> the Model 86 and all other Alpha dual 3CX800 amps, never used and last one
> left.
> Sections are 7-60pf and 15-210 pf (200 on the schematics) It has three heavy
> duty wipers as shown in the manual. Dimensions are the same as the OEP
> mentioned and I dont see how they came up with those values as I sold the OEP
> version thru Radiokit back then and it was the values I quoted for the
> Cardwell.
>
> Carl
> KM1H
>
>
>> Thanks Jim!
>>
>> I emailed them and they answered right back!
>>
>> They are $129.00 each in lots of 1 for the "75". 4 week delivery.
>> That will fit the bill exactly!
>>
>> I've had several ARD230 amps, but only the ones with 2 tubes.
>>
>>
>> Thanks for the tip!
>> 73
>> Jim W7RY
>>
>>
>>
>> -----Original Message----- From: Jim Garland
>> Sent: Saturday, June 21, 2014 12:23 PM
>> To: 'Jim W7RY'
>> Cc: amps@contesting.com
>> Subject: RE: [Amps] 2 Section Tune Cap Wanted
>>
>> Hi Jim,
>> Here's info on an OEP dual section capacitor that is fairly close to your
>> requirements: p/n 73-2-75-56BE, 2-sections, 17-65 pF and 25-318 pF, with
>> .075" spacing, nominal rating of 2500V. This is the cap that was used in the
>> ARD 230CA amplifier, which ran three 3CX800A7 tubes and covered 160m-10m.
>> You can easily swap plates between the two sections to obtain different
>> capacitance ranges, so long as the total number of plates remains fixed at
>> 56. The cap measures 2.5in x 2.5 in x 7.25 in, not counting the shaft. the
>> "75" in the part number refers to the .075" plate spacing, and if you change
>> that to, .e.g., 80, it would widen the spacing to .080" (and of course
>> change the dimensions). Other spacings are available in the same series.
>> 73,
>> Jim W8ZR
>>
>>> -----Original Message-----
>>> From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Jim W7RY
>>> Sent: Saturday, June 21, 2014 11:33 AM
>>> To: AMPS
>>> Subject: [Amps] 2 Section Tune Cap Wanted
>>>
>>> Now that I have found some 3CX800s and sockets (thanks to the list)!
>>>
>>> I'm looking for a 2 section air variable tuning capacitor like in the
>> Alpha amplifiers.
>>>
>>> 1 section around 50 pF and the other section 250 to 275pF. I'd even take a
>> 2 capacitors as
>>> long as I can hook them end to end (larger cap in the front) as seen here:
>> http://i900.photobucket.com/albums/ac206/w7ry/3CX800%20Amplifier/DSC_0112.jp
>> g
>>> Only problem with this is the assembly gets a bit long... So the dual
>> section would be best.
>>>
>>> I quickly looked on the Oren Elliott page but I don't see any pictures or
>> values. If someone
>>> has a part number, I could get one from them.
>>>
>>> Thanks and 73!
>>> Jim W7RY
>>> _______________________________________________
>>> Amps mailing list
>>> Amps@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/amps
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>> -----
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 2014.0.4592 / Virus Database: 3972/7731 - Release Date: 06/23/14
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|