As Rich Measures, and others has pointed out: be
careful of the filament voltage you are useing.
The filament voltage on many of these 5 volt tubes
should not exceed 4.9 vac. Any higher and you cut tube
life, and you wont get any more power. If you have
lots of money then go ahead, better yet take my advice
and send the savings to me :-) Call is good on qrz.com
73
STEVEN GRANT W4IIV
--- yo9fzs <yo9fzs@office.deck.ro> wrote:
>
> Hello Nermin,
>
> I tried this with a 4-400 and it wasn't working.
> The low R of the high current, directly heated, cold
> cathode caused the PC switcher to lock into
> protection
> state. Usually, these protection circuits locks the
> PS
> at (even for very short time) overloads, both for
> output +5V and for overvoltages.
>
> You may modify them for slow rising (ramp) of
> the output voltage. I used a potentiometer in the
> feedback circuit for adjusting the output voltages
> when "formatting/degasing" some tubes.
>
> Anyway, open the PS and look at the components.
> For "real" 20 amps continuous output, the 5V shottky
> rectifier have to be at 30 amps rated, output
> transformer
> EE33 core size, the output filtering capacitors to
> be
> 125 C deg type, the input filtering 330 to 470 uF
> and
> to have inrush current limitter (usually low R
> thermistor).
> It is also better if the switching power transistor
> to be
> not the usually TO220 case types, but larger ones.
>
> Many of these PS are overrated.
> I saw some of them rated at 25A/5V and 7A/12V
> having 20A in a TO220 case rectifier for the 5V,
> two 3A for the 12V output and EI28 core transformer.
> It were labeled "200W" and rated 5V/20A, 12V/7A,
> but the manufacturer warned us about the 100W total
> "real" output.
>
> Usually the PC switching PS are using the TL494 IC
> or equivalent at about 30 kHz switching freq.
> The ATX style have also a simple +5V at 0.5A
> switcher used for stand-by and for remote control.
>
> If you need I can send you a sample diagram.
> I'm servicing these for five years now...
>
> Maybe I'll use one (or two?) of these for a Harris
> RF110A amp (two 4CX1500B at 6V/10A each
> + two 8122 at 13.5V/1.3A each), if I'll not find
> a properly transformer...
>
> 73s and Good Luck,
> Traian
>
>
> Nermin Bajramoviæ wrote:
>
> > Hello list,
> >
> > having a number of PC power switching supplies
> laying around, usually 20
> > amps at 5v and 7-9 amps at 12 volts I wonder
> whether anyone of you, have
> > tried to use them for projects in amplifiers.
> Guess 5v could be used for
> > heating 8877, 3-500Z etc.. 12V for other lamps as
> well. Any ideas or clues,
> > surge capabilities. Oh, yes I have seen the Amp
> project of K5AM in QEX but
> > he did not use the power switchers.
> >
> > Thanks Nermin S58DX
> >
> > --
> > FAQ on WWW:
> http://www.contesting.com/FAQ/amps
> > Submissions: amps@contesting.com
> > Administrative requests:
> amps-REQUEST@contesting.com
> > Problems:
> owner-amps@contesting.com
>
>
> --
> FAQ on WWW:
> http://www.contesting.com/FAQ/amps
> Submissions: amps@contesting.com
> Administrative requests:
> amps-REQUEST@contesting.com
> Problems: owner-amps@contesting.com
>
__________________________________________________
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/
--
FAQ on WWW: http://www.contesting.com/FAQ/amps
Submissions: amps@contesting.com
Administrative requests: amps-REQUEST@contesting.com
Problems: owner-amps@contesting.com
|