Well done Lou.
I find it enough of a challenge actually reading the Ameritron circuits,
let alone verifying if the wiring is correct.
Dunno why they can't use normal circuit drawing techniques.
Its probably how mistakes like this happen in the first place.
73, Alek
VK6APK
On 14/10/2013 7:48 PM, Louis Parascondola wrote:
-----Original Message-----
From: Louis Parascondola<gudguyham@aol.com>
To: jim.thom<jim.thom@telus.net>
Sent: Mon, Oct 14, 2013 7:15 am
Subject: Re: [Amps] Ameritron AL-82/1200/1500 amps mis-wired!
Jim, the interlock on these amps simply opens one leg of the 240v primary. When the cover is off the switch
is open and if the amp is turned on the HV transformer will not get primary volt, hence no HV. BUT....due to
the mis-wiring a path through the relay coil creates a small voltage (primary AC) that when rectified gives
400vdc with S5 (safety interlock switch) in the power supply and on the anodes. If you look at the schematic
(which is correct) you won't see why it happens but with the mis-wiring, it happens. I emailed Ameritron the
other day and got a response from MIKE. Mike said they knew about the problem and at some point in time they
started to re-wire the units. HOWEVER...their "fix" still does not make the wiring conform to the
schematic but the "fix" does stop the 400vdc. The fix is a band aid. Because the wiring is still
wrong the step start circuit does not delay an additional 100ms. The schematic shows that the step start
relay coil is to charge up through the 10 ohm step start resistor which is supposed to delay the relay
closure by 100ms, add to that the 20ms of the contact closure time and you get 120ms of delay. With the
"fix" you only get the 20ms of actuate time. If you know anything about these amps you would know
that it is an ongoing problem that the step start relay contacts eventually weld shut. I have replaced many
of them in 20 years. That whole circuit needs to be wired properly according to the schematic to satisfy
both the HV leakage problem and the step start problem. UNFORTUNATELY ALL units in the field have either
both or one of these problems. NO units in the field are wired 100% correctly. EVERY unit out there needs
to be modified to reflect the schematic 100%. To save you the trouble of doping out the circuit, I have
already done the doping out and figured out what needs to be done. There is also another wiring error, but I
am not sure if they intentionally did a change and did not update the schematic. The primary wiring does not
conform to the schematic either. The schematic shows that in the event either of the main 15A fuses blow the
amp would completely shut down. HOWEVER....the way the units are wired if one particular main fuse blows the
filament transformer still operates and you get blower, lights, and filament voltage, but you loose HV. This
can cause you to continue to drive the tube with no HV present on the anode. The grid current goes very high
and I suppose damage to the tube can occur. The filament transformer has a separate small 4A fuse to protect
it but the line feeding it comes off the line side of the main fuse, hence if that main fuse blows the amp
does not go completely dead as you may expect. The fix of course is to move the feed to the load side of the
fuse as the schematic shows. They may have intentionally made this change but it is up to you to configure
your unit the way you want. Lou
-----Original Message-----
From: Jim Thomson<jim.thom@telus.net>
To: amps<amps@contesting.com>
Sent: Mon, Oct 14, 2013 5:24 am
Subject: [Amps] Ameritron AL-82/1200/1500 amps mis-wired!
Date: Sat, 12 Oct 2013 07:04:48 -0400 (EDT)
From: Louis Parascondola<gudguyham@aol.com>
To: amps@contesting.com
Subject: [Amps] Ameritron AL-82/1200/1500 amps mis-wired!
For those of you who might have any of these amps, they are mis wired. Seems
that pretty much all of them going back quite some time. They are not wired
according to the schematic and therefore a possible shock hazard is possible.
One might assume that when interlock switch S5 is open (cover removed) that
there is ZERO high voltage in the amp. But due to the mis wiring there is about
400vdc which is in the power supply and on the tube anodes. I suggest you
"CAREFULLY" make the test to your amp to see if the problem exists. Simply
remove the cover and turn the amp on and look at the HV meter. If you get any
reading other than zero, your amp is mis-wired and you should consider wiring it
properly. The fix is simple. There is a blue/white wire coming from the
contactor relay going over to the step start relay at junction with R3. There
is a wire on S5 (on left contact as viewed from front). These 2 wires need to
be switched to conform to the schematic. In doing so, th
e 400vdc with S5 open goes away. Although the manual states never to plug the
amp in with the lid off, I know many of us do troubleshooting and we may wrongly
assume that no HV is present when S5 is open. If you are not qualified to make
the repair, ask someone that is to do it for you. I believe this is a repair
that should be made to all these amps that exhibit this problem. Please be
careful in making the test or doing the repair. Lou
## I have NOT looked at the schematic. Does the Interlock short the B+ to
the chassis..or does it open off the 240vac to the plate xfmr....or both....or
what ??
Is the problem on older amps... or newer vintage versions?? IE: how
widespread is the issue ? Surprised somebody hasn’t fried themselves already.
Either way, the correct procedure would be.... to also chassis ground the B+
with an alligator clip. Then you know its at zero volts. Clip goes on
1st....and comes off dead last.
Then if something else goes wrong...... you are covered. If you want to be
super safe, use 2-3 clips..and grnd the B+ in two different places...like the
anodes, and the B+ end of the
string of HV filter caps. Another good place is directly between the B+ and
B- of the string of filter caps.
## Ameritron of course, should be notified. Its not a design issue, its an
assembly issue. IF you have the SNs, they may be able to track it down to a
specific employee or
group of employees. If they cant, they truly are idiots.
## So much for any kind of testing of the finished product. IE: step 1,
check interlock, does Vdc and or ACv drop to zero ? If not, check wiring
XXX.
Damned good thing they are not building medical or military or aircraft
equipment.
Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
--
From sunny Binningup, Western Australia.
Family Businesses:
Petkovic Air& Gas. petkovicag@bigpond.com
SP Electrical. www.spelectrical.net.au
Hampers by Hand. www.facebook.com/hampersbyhand
http://www.qrz.com/db/vk6apk
http://www.qrz.com/db/vk6ap
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|