Amps
[Top] [All Lists]

Re: [Amps] SB-200/ SB-220, HL-1000 etc

To: <k1sg@aol.com>, <amps@contesting.com>
Subject: Re: [Amps] SB-200/ SB-220, HL-1000 etc
From: "k7rdx" <k7rdx@charter.net>
Date: Mon, 30 Nov 2009 21:11:12 -0800
List-post: <amps@contesting.com">mailto:amps@contesting.com>
How hard is it to put a small standby/operate switch in a plastic mini-box 
in line with the PPT relay cable? No holes required ,better resale 
value,preserve the "Beauty" of the old beast...Jim..K7RDX...
----- Original Message ----- 
From: <k1sg@aol.com>
To: <amps@contesting.com>
Sent: Monday, November 30, 2009 8:50 PM
Subject: Re: [Amps] SB-200/ SB-220, HL-1000 etc


>A very easy solution for a standby switch for the SB-220/221  series...
> The front panel is held on with 4 screws.  I drilled out the hole for  the
> screw on the lower left corner, installed a mini-toggle switch there. 
> Since
> I had previously added a small relay, so T/R was only switching 12 volts,
> this  became a trivial fix for the lack of a standby/operate switch.
>
> Steve
>
> Steve  Gilbert
> K1SG
> K1SG@AOL.com
> 508-435-9133
> FN42fe
>
>
> In a message dated 11/30/2009 7:38:49 P.M. Eastern Standard Time,
> amps-request@contesting.com writes:
>
> Message:  7
> Date: Mon, 30 Nov 2009 17:18:19 -0500
> From: Jeff Carter  <amps@hidden-valley.com>
> Subject: Re: [Amps] SB-200/ SB-220, HL-1000  etc
> To: amps@contesting.com
> Message-ID:
> <c4eff4d0911301418s620adaacva2359d46d853d263@mail.gmail.com>
> Content-Type:  text/plain; charset=ISO-8859-1
>
> Where were you when I needed  you?
>
> That would have been a fantastic addition to my SB-220  rebuild.  I
> originally intended to use an original switch but couldn't  find a good 
> one
> and bought a generic one.  It would have been just as  simple to do what 
> you
> did while I had it all apart.
>
> Great  idea!
>
> Jeff/KD4RBG
> http://www.kd4rbg.com
>
> On Mon, Nov 30, 2009  at 4:10 PM, Edwin Karl <edk0kl@centurytel.net> 
> wrote:
>
>>
>> To add standby to an SB-200 I replaced the output  meter power control
>> pot to one with a push pull on off switch. On my  SB-220 I added a new
>> metering switch with an extra position and used  the second wafer to
>> open the keying lead. Always bothered me to turn  these things on and
>> off when using the exciter to adjust the antenna  matcher. Didn't want to
>> cut the  cabinet.
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.426 / Virus Database: 270.14.88/2537 - Release Date: 11/30/09 
21:05:00

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>