That really has no bearing on typical old technology ham tubes.
A lower gain tube requires higher negative bias in order to maintain a
reasonable ZSAC. It then requires sufficient RF to overide that bias.
You can easily compute the power required in Class B GG as well as the
low driving impedance, both of which require real power to overcome.
Many tubes dont have the grid dissipation available to do this.
Carl
KM1H
----- Original Message -----
From: "Bill Fuqua" <wlfuqu00@uky.edu>
To: <amps@contesting.com>
Sent: Wednesday, March 11, 2009 4:56 PM
Subject: Re: [Amps] 810 Linear Amp
> Triode tubes don't have to have high mu to be operated in grounded
> grid.
> You may loose a little power gain but
> not necessarily as bad as you many think.
> Here is a fine example
> http://www.mif.pg.gda.pl/homepages/frank/sheets/088/3/3CX10000A3.pdf
> 3CX10,000A3 has a amplification factor of 20. But in class AB2
> grounded
> grid operation its power gain is
> about 10 db. or factor of 10. Even in class C grounded grid it is
> not so
> bad.
> The high mu tubes allows you to operate zero bias or nearly zero
> bias
> with a bit more power gain.
> Also, the input impedance is higher.
> This is an EIMAC data sheet. I am not making this up. As I had said
> in
> before. One of my early amplifiers
> was a pair of 250TH tubes which were not particularly hi mu tubes
> (37).
> drove them with a pair of 6146B's and
> at a full gallon in the 60's. I am glad that I did not know then that
> low
> mu tubes could not be used in
> grounded grid. Strangely enough, the 250TH was considered hi mu by
> EIMAC
> then. H was for high and
> L was for low .
> I believe this idea may have started back in the transceivers could
> not
> drive high impedances and
> many grounded grid amplifiers did not have impedance matching networks
> in
> them. That is just a guess.
> With a amplification factor of 36 I would not be surprised that
> you
> could get 1000watts out with 100 watts drive.
> You may not get a full gallon but I don' think you need several
> hundred
> watts to drive it.
>
>
> 73
> Bill wa4lav
>
>
>
>
>
>
> At 04:11 PM 3/11/2009 -0400, Carl wrote:
>>With only a mu of 36 you would need a couple of 811's to drive them
>>and
>>the voltage swing needed would have them sounding like a CB amp.
>>
>>Great Class C RF or B modulator tube. I use a pair as modulators for
>>one
>>of the big old style amps here.
>>
>>Carl
>>KM1H
>>
>>
>>----- Original Message -----
>>From: "George Knight" <gkve3ltu@sympatico.ca>
>>To: <amps@contesting.com>
>>Sent: Wednesday, March 11, 2009 3:15 PM
>>Subject: [Amps] 810 Linear Amp
>>
>>
>> > Hi All,
>> > I am considering using four 810 triodes parallel connected in a
>> > grounded grid amp. Plate voltage would be about 2500 v. and
>> > expected
>> > output power should be close to a kilowatt. Has anyone in the group
>> > made such an animal, and if so, how did it turn out and what
>> > pitfalls
>> > should I avoid? Any info on operating parameters such as bias would
>> > be
>> > very welcome.
>> > Thanks and '73 ,
>> > George, VE3LTU.
>> > _______________________________________________
>> > Amps mailing list
>> > Amps@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/amps
>>
>>_______________________________________________
>>Amps mailing list
>>Amps@contesting.com
>>http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|