Hi Bill, I remember that argument,too, but It doesn’t carry much
water with today’s uniform components. The back resistance of a series
string of diodes is so high that I doubt an uneven capacitive voltage
divider would cause problems. Normally one designs an HV diode bank
with at least a breakdown voltage safety factor of 2, and preferably
more.
73,
Jim W8ZR
Sent from my iPhone
> On Dec 12, 2022, at 10:19 AM, hzp_electronics@juno.com wrote:
> Hi Jim
> The best argument that I have heard about capacitors across diodes is that
> older diodes had uneven capacitance. Under certain conditions the
> capacitance would cause the voltage to divide unevenly between the diodes.
> The added capacitors were made large enough to swamp out the capacitance
> difference and keep the voltage division more equally.
> \
> Whether the caps are needed with modern diodes, depends!
> 73
> .... Bill K3HZP
>
>
> ---------- Original Message ----------
> From: MU 4CX250B <4cx250b@miamioh.edu>
> To: Tim Duffy <k3lr@k3lr.com>
> Cc: jim.thom@telus.net, amps@contesting.com
> Subject: Re: [Amps] .01uf caps across diodes ?
> Date: Sun, 11 Dec 2022 22:32:29 -0800
>
> Hi Tim,
> I’ve followed this debate for years and frankly I don’t think adding
> .01uF caps across each diode in a diode string makes much difference
> one way or the other. It’s true that there will be some suppression of
> fast current and voltage transients, but these aren’t likely to cause
> damage to modern components. To me the downside of the practice is
> that adding 0.01uF caps results in additional opportunities for
> capacitor failures, loose solder connections, unsightly wiring, and a
> bunch of extra components that provide minimal benefits. I’m inclined
> to leave them out. (BTW, one commenter suggested that sharp voltage or
> current spikes wouldn’t make it through the filter capacitors. That’s
> untrue because the filter caps have a self inductance that keeps them
> from filtering spikes with high frequency components. )
> 73,
> Jim W8ZR
>
> Sent from my iPhone
>
>> On Dec 11, 2022, at 7:03 PM, Tim Duffy <k3lr@k3lr.com> wrote:
>>
>> W8ZR Jim
>>
>> Can you give advice on this topic?
>>
>> 73
>> Tim K3LR
>>
>> -----Original Message-----
>> From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of jim.thom
>> jim.thom@telus.net
>> Sent: Tuesday, November 29, 2022 2:28 PM
>> To: amps@contesting.com
>> Subject: [Amps] .01uf caps across diodes ?
>>
>> What's the consensus on wiring .01uf disc caps across diodes in a HV supply
>> ?
>> W8JI sez they are required, and used in ameritron amps....and used to
>> eliminate switching transients.
>>
>> Some say the caps are required to meet emc specs on commercial gear.
>>
>> I can't see how anything can get past the HV fitter caps.
>>
>> KM1H also uses caps across diodes. He also used another method, with a
>> .01uf cap across an entire series string of diodes, like a .01uf @ 5 kv
>> type.
>>
>> Orr's books recommend caps across diodes... to eliminate noise on TX on
>> ssb. .
>>
>> Are they required...or not ?
>>
>> Jim VE7RF
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|