Karlnet
[Top] [All Lists]

RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards

To: "'Karlnet Mailing List'" <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
From: "Dan Metcalf" <dan.metcalf@wbsysnet.com>
Reply-to: Karlnet Mailing List <karlnet@WISPNotes.com>
Date: Fri, 28 Mar 2003 18:21:37 -0500
List-post: <mailto:karlnet@WISPNotes.com>
The senao cards I have used seem to over heat and RX became a
problem.... are you able read the signal's?

Dan Metcalf
Wireless Broadband Systems
http://www.wbsysnet.com/
781-577-2780
dan.metcalf@wbsysnet.com
 

> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Caleb Carroll
> Sent: Friday, March 28, 2003 4:27 PM
> To: Karlnet Mailing List
> Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
> 
> These cards are all pretty much identical and Zcomax cards are just
> expensive.  We have a shitload of EnGenius cards (re-branded Senao)
and
> they've been working fine for months (as long as you're using
TurboCell
> and not 802.11b of course).
> 
> We're using the EnGenius cards with RG-1100's and AP-1000's though, so
I
> can't help Don with this problem but somehow I doubt that the problem
is
> with the Senao cards.
> 
> *********** REPLY SEPARATOR  ***********
> 
> On 2003-Mar-28 at 10:14 AM Charles Chia Sheng Wu wrote:
> 
> >Senao cards are crap, use the Zcomax cards
> >
> >-Charles
> >
> >-----Original Message-----
> >From: karlnet-bounces@WISPNotes.com
> >[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Don Starnes
> >Sent: Friday, March 28, 2003 9:57 AM
> >To: Karlnet
> >Subject: [Karlnet] WPBASE+ with SENAO 200mw radio cards
> >
> >
> >Hello everyone,
> >
> >I am having a hard time trying to get the new WPBASE+ to work with
SENAO
> >200mw (Intersil 2.5) or 100mw (Intersil 2.0) radio cards.  The board
> >recognizes the radios and will let you program them as usual.  The
> problem
> >seems to occur after they have been in service for a few hours.  I
get
> very
> >erratic behavior from the boards such as:
> >1. Second radio stops working
> >2. Second radio disappears
> >3. Port shows empty PCMCIA when I know there is a card in it.
> >
> >I know everyone's setup can be different.  We are using 12v 10a power
> >supplies to power these boards.  We have version 4.43a bin file on
the
> >radios.
> >
> >Any suggestions?
> >
> >Thank You,
> >
> >Don
> >
> >
> >_______________________________________________
> >Karlnet mailing list
> >Karlnet@WISPNotes.com
> >http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >_______________________________________________
> >Karlnet mailing list
> >Karlnet@WISPNotes.com
> >http://lists.wispnotes.com/mailman/listinfo/karlnet
> 
> 
> 
> 
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> ---
> [This E-mail scanned for viruses by Declude Virus]


---
[This E-mail scanned for viruses by Declude Virus]

<Prev in Thread] Current Thread [Next in Thread>