Ian,
Who did you contact in Tech Support?
I am suprised that you did not receive a response from them. Please let me
know so I can look into this.
Kevin
-----Original Message-----
From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Ian Hastie-Linkit
Sent: Tuesday, March 18, 2003 4:36 AM
To: Karlnet Mailing List
Subject: RE: [Karlnet] Help - Can a SEC client load Run WEPPlus?
Thanks Larry,
That explains my bench test results yesterday.
When bridging the SEC just doesnt pass anything wireless - wired. You can
ping & Manage the SEC from the AP and Ping and manage the SEC from the wired
side of the SEC but nothing in between.
I'll try it to a BG2000 tomorrow with NAT enabled or some routing set.
Karlnet are not exactly bursting with a response so far either so I'll just
have to work it out for myself again.
Regards
Ian Hastie
LINKIT
NEW ZEALAND
www.linkit.co.nz
-----Original Message-----
From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Larry Yunker (Cyber
Broadcasting)
Sent: Tuesday, March 18, 2003 12:41 AM
To: ian@linkit.co.nz; Karlnet Mailing List
Subject: Re: [Karlnet] Help - Can a SEC client load Run WEPPlus?
As far as I am aware, a Karlnet SEC client can connect to any 802.11b
compliant AP when the CPE is placed in routing-mode or when the CPE is
placed in NAT-mode. Bridging mode is different.
A Karlnet SEC CPE will only bridge through a Karlnet SEC AP. I do not know
if Karlnet has a SEC AP firmware that supports WEPPlus. That would be a
question for Karlnet themselves.
Good Luck.
Larry
----- Original Message -----
From: "Ian Hastie-Linkit" <ian@linkit.co.nz>
To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Sent: Sunday, March 16, 2003 2:38 PM
Subject: [Karlnet] Help - Can a SEC client load Run WEPPlus?
> Objective: to use an RG SEC as a client bridge to a WEPPlus enabled AP.
>
> First steps on the bench is using the Silver cards and I will use GOld
cards
> once I know it works OK.
>
> So I have just setup an RG SEC Client running (SR4500) with an Orinocco
> Silver card
> I set up an RG as an AP500 Access Point.
> Both Silver cards were loaded with WSU10872 for the lastest WEP
> drivers.(WEPPlus ready)
>
> I can ping Wired side of the AP all the way down the the RG SEC IP address
> but cannot ping anything beyond there on its wired side.
> All are set to bridge on the same subnet, same network name, NO WEP
enabled
> at this stage.
>
> I have;
> - reinstalled the SEC load just in case, setting the card for 802.11b
> wireless.
> - The configurator monitor shows the port is forwarding and have a wired
> client attached each
> side.
> - Tested all cables end PC- end PC & all Link lights are on.
> - RF LINK tests work OK Both ways, Client can see the AP and AP can see
the
> Client but no TCP/IP
> traffic passing.
> - I cannot manage the AP from the SEClient wired side however yet it can
see
> the RF Link from the
> AP.
> - I can manage the AP and SEClient RG's from the wired side of the AP.
>
> I will take the Silver cards back to WSU8.10 and check it works as I have
> other RG's working this way.
>
> Anyone done this before? Anything I missed?
>
> I suspect the Latest Prox/orinoco WSU isnt Karlnet compatible.
>
>
> Regards
> Ian Hastie
> LINKIT
> NEW ZEALAND
>
> www.linkit.co.nz
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|