Could that also be changes in the video scene being radiated? In general, the
power supply will be rather hummy and its frequency may drift. When I heard a
plasma TV, it was very stable with frequency, but the nature of the sound
changed with the video changes.
From: Mike Martin <mike@rfiservices.com>
Sent: Thursday, December 6, 2018 10:39 AM
To: Hare, Ed W1RFI <w1rfi@arrl.org>
Cc: Dave Cole (NK7Z) <dave@nk7z.net>; Rfi List <rfi@contesting.com>
Subject: Re: [RFI] 160 Meter RFI
I totally agree with Ed.
One fairly consistent rule is if the noise changes rapidly like within seconds
constant changes would indicate a TV power supply. The TV power supply load
changes with the demand for video and changes in the video so it changes the
load on the power supply causing the sound of the noise to change as rapid as
the video changes.
>From Mike's Mobile Email
Sent from BlueMail<http://www.bluemail.me/r?b=14013>
On Dec 6, 2018, at 10:30 AM, "Hare, Ed W1RFI"
<w1rfi@arrl.org<mailto:w1rfi@arrl.org>> wrote:
Switchers generally show the following characteristics:
They create noise every N kHz over a broad frequency range, with N typically
being 10 to 100 kHz.
The may be on continuously, but may also come on or off depending on whether
the equipment they are powering is being used
Some are on continuously to enable instant on functions, but will often change
the nature of the noise they create when powered equipment it turned on and off
Noise levels can vary as different lights and other equipment in a building is
turned on and off
They typically drift slowly with temperature changes
They usually respond to voltage fluctuations with slight changes in frequency
You really don't want to ask, "what is it?" If someone told you that your noise
appears to be coming from a Noisyo model XYZ-1 power supply, unless you knew
you had one in your own house, you would then move on to the real question:
Where is it? And if a Raucuso model ABC supply had the same characteristics so
your Noisyo identification was misleading, you might be looking for the wrong
device. Finding where it is, isolating it by flipping breakers then looking at
what may be plugged in to that circuit is more reliable.
If the noise is being radiated by a house, a good DFing loop and triangulation
may pin point the house. You can also get a good idea of where the noisy
device is by using a handheld AM or SSB mode receiver with an S meter. If you
position yourself a foot away from different house electrical wiring (external
light, power meter), the house with the noisy device will generally be much
louder than the others. If the noise is being heard over a wide geographical
area, if you go from pole transformer to pole transformer and put the receiver
with a short antenna about a foot from the ground wires of the poles, or a foot
from pad-mounted distribution transformers, the one with the house with the
noisy equipment will generally be louder.
Now, you can still be misled, because other houses may have noisy devices, too,
so the best way to find the source is to hear if from your own station, then be
able to follow it down the lines until it gets stronger at one house or one
pole.
Ed, W1RFI
-----Original Message-----
From: RFI <rfi-bounces@contesting.com<mailto:rfi-bounces@contesting.com>> On
Behalf Of Dave Cole (NK7Z)
Sent: Wednesday, December 5, 2018 5:29 PM
To: rfi@contesting.com<mailto:rfi@contesting.com>
Subject: Re: [RFI] 160 Meter RFI
Hi Ray,
Trying to guess the source from looking at captures can be tough...
That said, here are a few questions:
1. Does it ever change sound?
2. Does it run on a schedule?
3. It is always the same?
4. Is it just on 160?
If it runs on s schedule, kill your house power at one of the run times for it
to test if it is in your home...
It looks like a SMPS. Once you get proof it is not in your home, buy or better
yet, build a loop.
Look over Jim's paper, it does make a difference for the better, if you follow
his steps for quieting down your RF environment.
Take a look at my page at:
https://www.nk7z.net/sdr-rfi-survey-p1/
That is part I of a two part series on getting to know your RFI environment
using an SDR. There are several other links on the right dealing with RFI as
well...
73s and thanks,
Dave (NK7Z/NNR0DC)
https://www.nk7z.net
ARRL Technical Specialist
ARRL Volunteer Examiner
ARRL OOC for Oregon
On 12/5/18 9:10 AM, Ray wrote:
I have this 160 Meter RFI : https://youtu.be/QI08sE2FS40 It shows up
once or twice an hour for 5 to 10 minutes. Any ideas what it is?
Thanks,
Ray K9RS
________________________________
RFI mailing list
RFI@contesting.com<mailto:RFI@contesting.com>
http://lists.contesting.com/mailman/listinfo/rfi
________________________________
RFI mailing list
RFI@contesting.com<mailto:RFI@contesting.com>
http://lists.contesting.com/mailman/listinfo/rfi
________________________________
RFI mailing list
RFI@contesting.com<mailto:RFI@contesting.com>
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|