This is a pretty big release! Was able to spend some time finally
getting to the pile of e-mail I have been holding. I still have
about 100 messages to deal with, but am out of time before the
"Dayton" release.
After Dayton - I will try to spend some quality time with POST and
take care of some of the issues there.
If you make it to Dayton, stop by booth 444 and say hi.
73 Tree N6TR
Release notes for TR Logging Program - Version 6.40
7 May 1999
Version 6.40 - Released on 7 May 1999
- Improved showing of beam headings grids during entering them in the
exchange window. Also when coming from TRMASTER as initial exchange.
- Made initial exchanges from TRMASTER that are DomesticQTHs show their
mult status when coming up in the exchange window.
- Allowed TR to be started up with the prefix of a config file specified
which will automatically start that contest up (no selection screen).
- Fixed sent RST not being used with TR READ.
- Made /P calls not drop the /P when doing lookups in TRMASTER except
for name or FOC numbers.
- Fixed IS0 with wrong QSO points and exchange in ARI test.
- Fixed NAME FLAG ENABLE not working (name flag was always enabled).
- Fixed VE0 in RAC contest so it takes a serial number, but still counts
for 10 points.
- Created P13.DOM with VY0 added for RAC contest.
- Added ROTATOR PORT and ROTATOR TYPE (= DCU1 or ORION). The ORION PORT
command is still supported. Use Control-P to send the rotator to
the last displayed beam heading.
- Added FT100 to radio list. However, I am not sure there was any
difference between this and the FT920 setting. Let me know if it
has any issues.
- Fixed USER 4 and USER 5 overwrite change commands in POST. They were
affecting USER 3 status instead.
- Added BAND MAP DECAY TIME (control-J, default = 60) in minutes. Note
this applies to entries as they are added to the band map. Entries
made with a different value will still decay with their old time.
- Added RST PREFECTURE as legal value for EXCHANGE RECEIVED. This is
used for the JA INTERNATIONAL DX contest. Note that the QTHs will
show up with a "p" in front of them when shown as multipliers.
- Changed prefecture multipliers for JA INTERNATIONAL DX contest to
domestic multipliers similar to ALL JA contest. Improved visability
of remaining mults during QSO process.
- Allowed six digit grid squares to be entered instead of four, but
still use four digits for the mult.
- Added PACKET LOG FILENAME command (control-J). When set to a filename,
all packet spots received will be saved to this file.
- Fixed RANDOM CQ MODE messing up the Control-J menu.
- Change DKT in OKOM.DOM to DKL.
- Updated intial CQ EXCHANGE for ROPOCO contest to 5NN ). Eliminated
postal code form start up questions. Added ROPOCO.DOM file and enabled
domestic multipliers.
- Added EUROPEAN SPRINT contest. Added EUROPEAN SPRINT as legal QSO
POINT METHOD. Added QSO NUMBER AND NAME as legal EXCHANGE RECEIVED.
- Added AUTO RETURN TO CQ MODE (Control-J - default = TRUE). When TRUE
and you press the RETURN key in S&P mode - with the cursor in the call
window AND no information in the call or exchange windows - you will
be put into the CQ mode and CQ MESSAGE F1 will be initiated.
- Fixed All Asian and All JA entries in log prompt.
- Many improvements to the All JA contest (previously released only in
Japan two weeks ago).
- Eliminated prefectures 115 to 118 in All JA.
- Pretty much gave up on Aurora stuff RSTs.
- Fixed sent RST not working when using [ character in exchange.
- Fixed LOOK FOR RST SENT not showing up in Control-J menu.
- Added Alt-N option for sending Control-J parameter to network. This
will send the hilighted Control-J paramter to all of the computers
on the network. The change will also be added to the config file
so that it will still be there if the program is restarted.
- Fixed missing exchange for MICH QSO PARTY outside of MI.
- Released a special 6.39 to Tack with All JA improvements including
remaining display, made precedence H/M/L/P and added prefectures 48-50.
Version 6.39 released on 16-Apr-99.
- Updated IOTA QSO Point method to new rules. You get 15 points for
working an IOTA other than your own. Otherwise, you get 3 points.
- Attempted to fix crash with big packet frequencies greater than 1 GHz.
- Made ZZ00 not be accepted as a legal grid square in exchanges.
- Made notes in LOGCFG file that start with ; require space before the ;.
This fixes problems with having ; enbeded in a string that might be
sent to a radio (like Kenwoods).
- Fixed garbage in call window when using the Control-B command with
Auto-CQ active.
- Fixed turning on of DVP in Control-J. Made DVP ON disappear when
turning off DVP from Control-J.
- Made PTT HOLD COUNT of 0 not "hang" PTT.
- Removed RST ALL JA PREFECTURE AND POWER exchange and replaced it
with RST ALL JA PREFECTURE AND PRECEDENCE exchange since the ALL JA
contest now uses a single letter (H, M, L or P) to identify power.
Allows most any order for exchange information, but no duplication
of entry data allowed. 57923C will work as well (RST 579, Pref = 23
and power = C). On CW, 23 579 C will also work, but on SSB, it won't.
- Fixed summary sheet not coming up for Russian contest.
- Added ask for your state if selecting any of the QSO parties from menu.
- Added MIGHIGAN QSO PARTY (OR MICH QSO PARTY). Make sure to either
run TR NEW and answer if you are in MICH - or put MY STATE = MI
in the LOGCFG.DAT file BEFORE your CONTEST statement if you are in
Michigan.
- Changed MQP to MN QSO PARTY (to avoid confusion with MICH QSO PARTY).
- Updated SP DX contest for non SP stations. Added SP.DOM.
- Added LOOK FOR RST SENT (false - Control-J). Allows sent RST to be
entered with S prefix in exchange field. Works with RS on SSB too.
- Allowed for aurora RS(T)s on 6 and 2 meters for both sent and received.
- Added RADIUS OF EARTH parameter (default = 0). Enter in meters.
When something is entered, the default internal to the program will
be overwritten.
- Fixed bug when trying to set a key (like start sending now) to ;.
Version 6.38 - 16 March 1999.
- Fixed name of domestic files for Wisconsin QSO Party.
- Fixed WWL contest multipliers:
- Grid fields instead of grid squares for mults.
- MULT BY MODE = FALSE
- Allowed ESCAPE EXITS SEARCH AND POUNCE in addition to ESCAPE EXITS
SEARCH AND POUNCE MODE in LOGCFG.DAT file. This eliminates an
incompatability with the name Control-J uses when saving this
command.
Version 6.37 - 11 March 1999.
- Added ESCAPE EXITS SEARCH AND POUNCE MODE. The default is FALSE and
it can be found on the Control-J menu. If you set it to FALSE, you
will have to use SHIFT-TAB to go back into the CQ MODE.
- Added RSGB QSO point method. This scores zero points for a QSO in
your own country, 5 points for Europe, 30 for Oceania and 15 for
the remaining continents.
- Added NAME FLAG ENABLE. The default is TRUE and it can be found
on the Control-J menu. When FALSE, the asterisks that appear in
the log when you know the name of a station are disabled.
- Fixed bug with unwanted CW being sent with QSL BUT NO LOG option.
- Added - to send 1.5 * dah length. This might be a cool chracter
to use for your leading zeros.
- Fixed summary sheet not working for Croatian and Minnesota QSO Party.
- Fixed some reports not working because they were always looking
for LOGCFG.DAT - even if you selected a different log.
- Added WISCONSIN QSO PARTY (or WQP).
- Fixed band map cursor position if multi info window is up.
- Added { character to send complete corrected callsign in call ok
message. Before, there wasn't a way to send the complete call
of the station you just finished working.
- Fixed null character appearing in multi notes.
- Tried to fix missing grids from band map updates in Stew Perry.
Version 6.36 - Released on 14 December 1998
- Added new startup command "TR NEW". This will bring you to the menu
to select a new contest. You will also be asked what filename you
want to save your files under.
- When starting up TR or POST with more than one config file present in
the working directory, a menu will be presented allowing you to select
which set of files you want to use.
- Added automatic CW exchange generation for ARRL 10. Assumes you have
MY QTH or MY STATE setup. If you are outside W/VE, it does the serial
number automatically as well.
- Made MY QTH which acts the same as MY STATE in LOGCFG.DAT.
- The band map will now update the multiplier status for all band map
entries when working a new station.
- Many fixes to WAE QTC routines if you are outside Europe.
- Fixed bug if you made over 600 QSOs.
- Allow you to view the QTC.DAT file with Control-L key.
- Put note in log when a QTC is finished.
- Improved some keystrokes to make sure accidents don't happen.
- Fixed bug with improper initialization of QTCs when restarting program.
- Added way to send a string to radio serial interface ports. These
are message commands, so you would program a function key to send
a message to the radio as follows:
<control-C>SRS=message<control-D> - Sends message to active radio.
<control-C>SRS1=message<control-D> - Sends message to radio 1.
<control-C>SRS2=message<control-D> - Sends message to radio 2.
Please see section 4.2 of the manual for more information on how
to use the control-C and control-D commands in a CW message.
For example, if you wanted to program a key to make your Kenwood
radio use the narrow CW filter, you would program the following
message:
<control-C>SRS=FL010009;<control-D>
You would program this by using the Alt-P command to access the
function key you want to program. Then press control-P followed
by control-C to enter the control-C character, then type "SRS=FL010009;",
then control-P and control-D to finish the command.
This command can also be used to activate the digital voice keyer on
some radios.
- Fixed bug with Alt-=. If you turned off the CW monitor tone with this
command while the tone was one, it would stay on.
- Fixed last total line of POST L C not showing up (band/mode logs).
- Not allow JA Prefectures > 50 to be entered.
- Went to European distance for European VHF QSO Point method. This
routine gives different distances than the normal routine. Will
someone in Europe please confirm if it is working as expected?
- SCP COUNTRY STRING allows ! or - at start to make it exclude countries
instead of including them.
- STDCFG.DAT is a file you can put in the same directory as your
TR.EXE file and the program will always execute it as if you had
used INPUT CONFIG FILE for it. It is executed after all the other
LOGCFG.DAT commands are processed.
- Made POST's L P (pull computer ID into log) command process notes.
- Added computer ID to notes added with Control-N.
- Made " clear RIT. This is because on most keyboards, you have to
press the SHIFT key to get to the " character and it makes the RIT
move when you probably didn't want it to.
- Fixed POST's R L from crashing.
Version 6.35 - Released on 2 December 1998
- Fixed a number of crash possibilities in some of POSTs report
procedures.
- Made TR READ keep computer IDs.
- Allowed for the space character as a computer ID in the POST utility
that pulls out QSOs made by one computer.
Version 6.34 - Released on 20 November 1998
- Added MODEM PORT. This can be used along with the multi port to
allow connection of a second port over a dedicated modem off a
second serial port on a computer. Also, MODEM PORT BAUD RATE.
- Fixed Control-F1 not working for DVP and DVK program. Using Control-F1
to Control-F10 will instantly allow you to re-record DVP or DVK memories
F1 to F1.
- Improved DVK and two radio stuff functionality.
- Changed WPX QSO Point method to give one point for own country
(regardless of band). This complies with the new rules coming
up next year.
--
FAQ on WWW: http://www.contesting.com/trlogfaq.html
Submissions: trlog@contesting.com
Administrative requests: trlog-REQUEST@contesting.com
Problems: owner-trlog@contesting.com
Feature Wishlist: http://web.jzap.com/n6tr/trwish.html
|