I just checked my O2 - when you hit A>B or B>A, the mode does transfer,
as does the BW and PBT if they are set to track in the RX Menu
I'm using 2.032 firmware
Dave K5WNV
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com] On Behalf Of Bob Henderson
Sent: Wednesday, April 19, 2006 4:10 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters!
AlsoeffectsO2v2.032!
This IS a problem Larry. When you need to split you shouldn't need to
remember the mode you last used on the second VFO. You just want to
split.
The solution is simple. A>B or B>A should transfer mode as well as
frequency. Who wants to split frequency and mode at the same time?
Nobody I know, that's for sure. I've lost count how many times this fix
has been asked for.
I don't know why but this seems to be a concept the fellas at Ten Tec
struggle with.
Bob, 5B4AGN
----- Original Message -----
From: "Larry Menzel" <retire@means.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, April 19, 2006 3:04 PM
Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also
effectsO2v2.032!
> Whoa. Isn't there an offset between SSB and CW normally? 1.5kc sounds
about
> right. This does not seem like a bug to me.
>
> And why would you want to transmit in different modes when working
> split anyway?
>
> Isn't this twisting things just a bit, or am I missing something? I
> know that when I go split, I am ALWAYS in the same mode.
>
> I admit that I'm easily confused, but this doesn't seem like a
> problem.
>
> Larry, N0XB
>
>
> ----- Original Message -----
> From: "Carl Moreschi" <n4py@arrl.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Tuesday, April 18, 2006 10:11 PM
> Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects
> O2v2.032!
>
>
> > If you are going to transmit on VFO B, the mode must be the same on
> > the main and sub receiver. There is definitely a bug a here.
> >
> > Carl Moreschi N4PY
> > 121 Little Bell Drive
> > Bell Mountain
> > Hays, NC 28635
> > ----- Original Message -----
> > From: "Lin Davis" <linbdavis@earthlink.net>
> > To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> > Sent: Tuesday, April 18, 2006 9:59 PM
> > Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also
> > effects
O2
> > v2.032!
> >
> >
> >> Orion operators, be careful if you assign TX to VFO B.
> >>
> >> Like Randy, I also found a TX frequency error, 1500 Hz worth, on my
Orion
> > II v2.032.
> >>
> >> My setup:
> >>
> >> On 40 meters:
> >> Assign TX and SubRX to VFO B.
> >> Assign RX to VFO A.
> >> Set MainRX mode to LSB.
> >> Set SubRX mode to LSB.
> >>
> >> Using an independent receiver to listen to the output, I pressed
> >> TUNE, and
> > zero
> >> beat the tx signal. I spoke into the microphone (connected to front
panel
> > conn.)
> >> and heard my voice right on frequency.
> >>
> >> Then I changed MainRX mode to LCW.
> >>
> >> Pressing TUNE, I noted that the TX frequency did not change from
> >> above.
> > But when
> >> I spoke into the microphone, my speech was unintelligible. I had to
tune
> > the
> >> receiver 1500Hz down to hear my voice normally!
> >>
> >> BTW, Randy's scenario was as above but with SubRX mode set to USB
> >> and Main
> > RX to
> >> LCW.
> >>
> >> I checked and found that the shift isn't dependent on sidetone
> >> setting.
> >>
> >> I didn't check previous code versions.
> >>
> >> When I get a chance I'll try other combinations.
> >>
> >> 73,
> >> Lin
> >> WB1AIW
> >>
> >>
> >>
> >>
> >> Randy, K4QO, wrote:
> >>
> >> > Condition:
> >> > VFO A is on 30 meters LCW mode
> >> > VFO B is on 60 meters USB mode.
> >> >
> >> > Result:
> >> > VFO B receives on frequency but transmits 500Hz low of frequency
> > displayed.
> >> >
> >> > If VFO A is then changed to USB mode (and no other changes),
> >> > then
VFO
> >> > B
> >> > transmits on frequency displayed.
> >> >
> >> > 73,
> >> > Randy
> >> > K4QO
> >> > _______________________________________________
> >> > TenTec mailing list
> >> > TenTec@contesting.com
> >> > http://lists.contesting.com/mailman/listinfo/tentec
> >> >
> >> >
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|