You must upgrade to the LDG AT 200 PC to LDG firmware level 1.9. The loader
and firmware for this are available on the LDG website. LDG does not ship
the tuner with this firmware level. Also my Orion program must be at 1.30
or later.
73,
Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message -----
From: "Denton" <denton@oregontrail.net>
To: "Carl Moreschi" <n4py@arrl.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Friday, January 04, 2008 10:40 PM
Subject: Re: [TenTec] LDG tuner in O II?
> Hi Carl....purchased a new ldg at 200 pc and seem to have a problem with
> erratic performance....sometmes it works but most of the time your
software
> and it don't seem to communicate very well.
> Tried another 200 pc control program with the same results. Have tried
both
> the usb to serial port interface that came with the tuner plus another
known
> good usb to serial port interface.
> Sounds like a bad serial chip in the tuner...what do you think?
> ----- Original Message -----
> From: "Carl Moreschi" <n4py@arrl.net>
> To: <ken.d.brown@hawaiiantel.net>; "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Wednesday, December 26, 2007 12:11 PM
> Subject: Re: [TenTec] LDG tuner in O II?
>
>
> >I don't know any specifics for the LDG internal Orion tuner. Buit I am
> > quite familar with the LDG AT-200PC tuner. This tuner has built in
> > memories
> > that allow all the tuner settings to be saved by frequency. There are
> > several thousand memory slots to save the tuner settings. The slots are
> > spaced closely at the lower frequencies and are spread more widely at
the
> > higher frequencies. This allows the slots to be very optimized by
> > frequency. Once you have tuned the tuner on a particular frequency,
that
> > setting is saved in the appropriate memory slot. My N4PY program keeps
> > track of what frequency slots are saved in the tuner. When you return
to
> > a
> > frequency, this slot can be used to restore the frequency setting
without
> > the need to transmit. This makes the AT-200PC and ideal external tuner
to
> > use with many radios and my N4PY software.
> >
> >
> > Carl Moreschi N4PY
> > 121 Little Bell Drive
> > Bell Mountain
> > Hays, NC 28635
> > ----- Original Message -----
> > From: "Ken Brown" <ken.d.brown@hawaiiantel.net>
> > To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>;
> > <kamar@inr.net>
> > Sent: Wednesday, December 26, 2007 1:54 PM
> > Subject: Re: [TenTec] LDG tuner in O II?
> >
> >
> >> Sounds like a good method to me. I am curious about the LDG tuner. I
> >> presume the LDG has a built in frequency counter to address tuning
> >> memories for each frequency, or does it use a data connection from the
> >> transceiver to tell it what frequency to tune to when using memory
> >> tuning? In either case what is the frequency resolution? In other
words,
> >> if you were to tune it at 3.505 kHz and then again at 3.506 kHz, would
> >> it actually store two separate tuning settings, or would the first one
> >> at 3.505 get overwritten because the two are the same frequency when
> >> described with a resolution of 10 kHz? Also, how many memories does it
> >> have? Is the frequency resolution the same for all bands? It would make
> >> sense to me to use smaller resolution on the lower bands. You might
need
> >> five different tunings to cover 80/75 meters and only two each for 20
or
> >> 15 meters. If there is plenty of memory available it wouldn't matter.
> >>
> >> DE N6KB
> >> > I did above initial tuning every 10 or 20 KHz across
> >> > each
> >> > band.
> >> >
> >> > Then in 'normal' radio use and when changing bands or moving across a
> >> > band,
> >> > I 'tap' the Orion's Tune button. The LDG tuner quickly tunes (by
> >> > recalling
> >> > the match parameters from its memory) to the predetermined setting
near
> >> > or
> >> > on that frequency in its memory.
> >> >
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|