TenTec
[Top] [All Lists]

Re: [TenTec] Orion NR problem

To: tentec@contesting.com
Subject: Re: [TenTec] Orion NR problem
From: Duane A Calvin <ac5aa@juno.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 14 Jun 2005 23:30:27 -0500
List-post: <mailto:tentec@contesting.com>
Not sure, Steve, but I wonder if the degree to which the NR works might
be due to the characteristics of the noise?  I also remember it being
much more aggressive on the earlier FW versions, but just last night It
was so quiet on one band I was on that when a signal came on it about
blew my eardrum.  So, I see variable results, which, up until now, I've
considered were perhaps caused by the band noise characteristics. 
Perhaps not.

        73,  Duane


On Tue, 14 Jun 2005 21:58:37 -0400 "Steve N4LQ" <n4lq@iglou.com> writes:
> I don't recall the firmware revision my Orion had when I bought it 
> but I do 
> recall turning on the NR and my jaw dropping. It was awesome. All 
> the band 
> noise vanished and I none of the goofy dsp artifacts that most rigs 
> have. 
> Then I "upgraded" to a new firmware and the NR ceased to work. 
> Pushing the 
> button had a tiny effect but it was almost useless. I tried many 
> master 
> resets to no avial. I think we see different opinions here because 
> some NRs 
> are working and some are not or not much.
> Steve Ellington
> N4LQ@iglou.com
> ----- Original Message ----- 
> From: <K4IA@aol.com>
> To: <tentec@contesting.com>
> Sent: Tuesday, June 14, 2005 8:29 AM
> Subject: Re: [TenTec] Orion NR problem
> 
> 
> > Gary
> >
> > I sometimes find it hard to tell if the NR is working or not.  
> Band  noise 
> > is
> > still there.  But I find that if I let the NR "do its thing" the S 
>  meter
> > gradually declines and even though I still hear noise - it is at a 
>  much 
> > lower
> > level than before.  My natural inclination was to crank up the  
> audio gain 
> > a
> > little bit so I could "hear" the radio.  Then when a  signal comes 
> on, it 
> > really
> > jumps out at you.
> >
> > I have found that you must push the button firmly.  A partial push 
> or  a
> > light touch will change the display but not engage the NR. I know 
> that 
> > makes no
> > sense but that is the way it works on my Orion.  I use a setting  
> of 3 as 
> > I
> > find that reduces the noise in about a second or two with a 
> minimum of
> > distortion.
> >
> > k4ia
> > Craig  "Buck"
> > Fredericksburg, Virginia USA
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> > 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> ting.com/mailman/listinfo/tentec
> 
> 


--------------------------------------
Duane Calvin, AC5AA
Austin, Texas

http://home.austin.rr.com/ac5aa
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>