TenTec
[Top] [All Lists]

Re: [TenTec] Orion II Problem

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion II Problem
From: Billy Cox <aa4nu@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 16 Oct 2014 19:38:25 +0000 (UTC)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
How old is the backup battery in each of the respective Orions?

That might be a good next step to try, even if the battery is 
not that old, ... still cheaper than a trip to TT ...

(Other ideas might be master resets and reloading firmware)

Hope this helps!

73 de Billy, AA4NU

----- Original Message -----
From: "art N4UC" <n4uc@hotmail.com>
To: "TenTec reflector" <tentec@contesting.com>
Sent: Thursday, October 16, 2014 2:25:19 PM
Subject: Re: [TenTec] Orion II Problem

I have been experiencing the exact same problem for months with my Orion 565. 
It started out mostly only on 20M and would clear up if either changed bands or 
cycled the power. Then it progressed to other bands as well and now does not 
clear up regardless of what I try. It affected only the main rcvr, the sub was 
fine. Listen on a separate radio to  see if it also affects the transmitted 
signal. In my case the transmitted CW signal sounds just like the received 
signal audio, warbly and buzzing almost like a spark gap signal!. So I'm 
guessing it's somewhere in the local oscillator/IF chain.  I've talked to TT a 
few times and there's no way to diagnose my symptoms without getting it on the 
bench.

Currently it's sitting on the shelf unusable while I decide how much I want to 
spend on it. Good luck. If you think of it, drop me a note if you resolve the 
problem.

Art/N4UC

> From: Doug.Speer@FairbanksMorse.com
> To: tentec@contesting.com
> Date: Thu, 16 Oct 2014 13:37:22 +0000
> Subject: [TenTec] Orion II Problem
> 
> I am starting to believe my Orion II has developed a problem.  On the main 
> receiver I am hearing distorted, buzzing sounding signals that are well 
> outside the DSP and roofing filter bandwidth.  I am not hearing signals 
> outside the filter bandwidth on the RX-366 sub-receiver.  The problem is most 
> notable on 160m but to some extent present on 80m.  I don't really notice it 
> above 80m.  I have tried a master reset which did not resolve the problem.
> 
> Do any of you have any immediate thoughts or does the rig need to visit 
> Sevierville?
> 
> Doug, W9PN
> Janesville, WI
> 
> 
> ----------Legal Disclaimer----------
> 
> The information contained in this message may be privileged and confidential, 
> and is intended solely for the use of the named addressee. No other person is 
> authorized to access, copy or re-use this message (or any information 
> contained herein). If you are not the intended recipient, please notify us 
> immediately by replying to this message and delete it from your computer.
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
                                          
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>