TenTec
[Top] [All Lists]

Re: [TenTec] Model 411 amp (aka Centaur)

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Model 411 amp (aka Centaur)
From: Gary J FollettDukes HiFi <dukeshifi@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 26 Jan 2016 22:42:42 -0600
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I would indeed look at the caps again.

I remember now that one of them in mine had a metal bridge between the can and 
the positive screw terminal of the cap.



Gary
> On Jan 26, 2016, at 9:25 PM, Joe Papworth via TenTec <tentec@contesting.com> 
> wrote:
> 
> Thanks Gary. I eye-balled the caps today. I didn't see anything bad but I was 
> mainly looking for swelling.
> If it's not a tube, I'll take another look at the caps.
> 
> 
> Sent from AOL Mobile Mail
> 
> 
> -----Original Message-----
> From: Gary J FollettDukes HiFi <dukeshifi@comcast.net>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Sent: Tue, Jan 26, 2016 10:17 PM
> Subject: Re: [TenTec] Model 411 amp (aka Centaur)
> 
> 
> I fellow up in northern Minnesota GAVE me one of those with exactly the same 
> problem.
> 
> I found that one of the filter caps was pinched too hard during assembly and 
> must have distorted the capacitor.
> 
> I replaced them all anyway but I sure got a good deal when I was done with it.
> 
> The tubes could do it too, even key up because the plate voltage is still 
> applied to them in standby.
> 
> 73
> 
> Gary
> 
> 
> 
>> On Jan 26, 2016, at 10:25 AM, Al Sirois <<a 
>> href='mailto:alsirois@roadrunner.com'>alsirois@roadrunner.com> wrote:
>> 
>> Tuesday noontime, Joe:
>> 
>> I have a Centaur..............keep it covered when not in use.
>> 
>> My Elmer told me to always keep it covered..................dust is the 
>> problem.
>> 
>> Even when covered, open it up every two-three years and do a internal 
>> cleaning.
>> 
>> N1MHC/alsirois
>> =============
>> 
>> -----Original Message----- From: Joe Papworth via TenTec
>> Sent: Tuesday, January 26, 2016 8:50 AM
>> To: <a href='mailto:tentec@contesting.com'>tentec@contesting.com
>> Cc: <a href='mailto:k8mp@aol.com'>k8mp@aol.com
>> Subject: [TenTec] Model 411 amp (aka Centaur)
>> 
>> Gents,
>> 
>> 
>> Have any of you gone a few rounds with a Centaur amp?
>> I have a one that blows fuses very intermittently. It vaporizes them both, 
>> simultaneously, so it's apparently a dead-short somewhere. This happens even 
>> in stand-by. (i.e. No key-down)
>> 
>> 
>> Before I tear into it, anyone have any ideas of common failures in these 
>> amps?
>> 
>> 
>> Later, Joe, K8MP
>> 
>> _______________________________________________
>> TenTec mailing list
>> <a href='mailto:tentec@contesting.com'>TenTec@contesting.com
>> <a href="http: lists.contesting.com="" mailman="" listinfo="" tentec" 
>> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec 
>> _______________________________________________
>> TenTec mailing list
>> <a href='mailto:tentec@contesting.com'>TenTec@contesting.com
>> <a href="http: lists.contesting.com="" mailman="" listinfo="" tentec" 
>> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec
> 
> _______________________________________________
> TenTec mailing list
> <a href='mailto:tentec@contesting.com'>TenTec@contesting.com
> <a href="http: lists.contesting.com="" mailman="" listinfo="" tentec" 
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec
> </a href="http:></a href='mailto:tentec@contesting.com'></a href="http:></a 
> href='mailto:tentec@contesting.com'></a href="http:></a 
> href='mailto:tentec@contesting.com'></a href='mailto:k8mp@aol.com'></a 
> href='mailto:tentec@contesting.com'></a href='mailto:alsirois@roadrunner.com'>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>