TenTec
[Top] [All Lists]

Re: [TenTec] open wire feed/loops

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] open wire feed/loops
From: "k8bbm" <k8bbm@srt.com>
Reply-to: k8bbm@srt.com,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 02 Feb 2006 21:07:27 -0600
List-post: <mailto:tentec@contesting.com>
        at 2-3 wavelengths, you stop being a cloud warmer -
remember that at harmonics, the radiation begins to go in
the plane of the loop.  I've used a 160 mtr horiz loop on 80
mtrs and had wonderful performance.
Dave K8BBM                      
----- Original Message Follows -----
From: "Rob Atkinson, K5UJ" <k5uj@hotmail.com>
To: tentec@contesting.com
Subject: [TenTec] open wire feed/loops
Date: Fri, 03 Feb 2006 03:00:38 +0000
                                
>
> I tried to find the bare copper 450 ohm open wire feed
> with the ceramic or  white plastic spacers a couple of
> years ago, and after contacting 3 or 4  vendors who all
> had the plastic window line only, was finally told by
> someone that you can't get the bare copper feed anymore
> because in our world  of lawsuits, it was considered too
> dangerous for anyone to use.
>
> The only source i know of (besides making it yourself) for
> the genuine open  wire feed (i.e. not window line)  is
> W7FG as someone else mentioned.   This  what I use, and I
> have had no problems with it, but I can't compare it to
> window line because i have never used the 450 ohm window
> line.   For all I  know, it may be just as good more or
> less (or better?).
>
> I use pvc pipes stuck in the ground and topped with T
> sections to hold my  line up over the ground.  It enters
> my basement at a small casement window  that's 1.5 x 2.5
> feet and divided into 3 panes.  I bashed out the middle
> pane and replaced it with plexiglass that I drilled two
> holes in 3" apart.   I put banana jacks in these and
> terminated the line outside with plugs.    this makes a
> quick disconnect for thunderstorms.    on the inside I
> soldered  another foot or two of line to the jacks and put
> my transmatch on a shelf in  front of the window.  coax
> from there to the rig.     i was lucky to have a  ready
> made window--it almost looks like it was put there for the
> feedline.    As bob said, it's worth it to bring the line
> in some way, even if you have  to hire someone to saw a
> square out and put in a window.
>
> I have a question about the cloud burner loops.    If you
> have a low loop  that's only 20' off the ground but make
> it 2 or 3 lambda on 80 m. it seems  to me it will still be
> a cloud burner on that band.  Is this right or will  the
> length give you some lower angles?
>
> thanks,
>
> rob / k5uj
>
> __________________________________________________________
> _______ Express yourself instantly with MSN Messenger!
> Download today - it's FREE!
>
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>