I read the kudos on the chip so I bought it and then did some re-
reading from this pdf on the chip:
http://tentecwiki.org/lib/exe/fetch.php?id=562&cache=cache&media=omni_
v9.pdf
I originally thought the project was essentially to replace the
microprocessor alone, place something like pinstriping on the
frequency buttons and then relabel them and make a small change to
the data cable; all things that could be easily undone at any future
time when I decide to sell the radio. However, after reading the
above info, I realized that to make the changes suggested within the
radio would likely someday be an issue to me, a new buyer or
repairman. A deal's a deal so I'm keeping the chip but it's sitting
on the Omni & I'm not going to modify the radio.
Gary
ka1j
> Have you put N4PY's V.92 chip in the Omni V? It also requires that a
> cable described by Carl be made to get rig control to work. It didn't
> mention anything about USB. While not difficult now with the v.92
> chip, it's not plug'n play either.
>
> Mike, K9MI
>
>
>
> ----- Original Message -----
> From: "Gary Smith" <Gary@doctorgary.net>
> To: <Tentec@contesting.com>
> Sent: Wednesday, December 05, 2007 04:33
> Subject: Re: [TenTec] Logic 8 and Omni VII? - & now Omni V...
>
>
> > Sure enough, I have the same problem but with an Omni V
> >
> > Though I've had good luck with Logic as a logging software I 've now
> > tried getting the Omni V to interface with it and have not been able
> > to do so. I called Logic's tech help but didn't get things resolved.
> >
> > I know the USB cable is recgonized by XP, the "Prolific" drivers are
> > installed & working and the Omni V is ID'd in Logic as a known radio
> > but Logic still doesn't seem to know the Omni V is on the other end.
> >
> > The error message given on startup says
> >
> > "A timeout error occured when attempting to communicqate with a rig.
> > Make sure the rig is turned on and check cabling and setup
> > parameters
> >
> > POLLING DISABLED. 0 characters in buffer".
> >
> > All I want to do is have the frequency/band info get imported
> > automatically into logic.
> >
> > Anyone using Logic 8 with an Omni V especially if you're using a
> > RS232 to USB adapter?
> >
> > Thanks!
> >
> > Gary
> > KA1J
> >> I'm using Logic8 with an Orion II - works great - I've been using
> >> Logic8 since Logic5
> >>
> >> Dave K5WNV
> >>
> >> -----Original Message-----
> >> From: tentec-bounces@contesting.com
> >> [mailto:tentec-bounces@contesting.com] On Behalf Of Gary Smith
> >> Sent: Sunday, December 02, 2007 10:35 AM To: Discussion of Ten-Tec
> >> Equipment Subject: Re: [TenTec] Logic 8 and Omni VII?
> >>
> >> > Is anyone using Logic 8 logging software with their Omni VII? If
> >> > so, I'd like to talk about how you interfaced it. Thanks Tim Nz8J
> >>
> >> I use Logic 8 but haven't hooked it up yet to this newly acquired
> >> Omni V (need to either get a dedicated computer for ham that has a
> >> RS232 port or get a RS232 to USB adapter for my laptop.
> >>
> >> I called Dennis and he said the V will interface well with Logic 8
> >> with either the native controller chip or the N4PY V.92 mod chip
> >> I'm installing today. Hearing that from him, I'd expect the VII
> >> would interface as well.
> >>
> >> Gary
> >> ka1j
> >>
> >> BTW, I've used Logic since it was a DOS version back in 91, great
> >> program. Does so much more than I've ever had a need to do. He's
> >> made it pretty flexible.
> >> _______________________________________________ TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >>
> >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|