TenTec
[Top] [All Lists]

Re: [TenTec] Two Century 21 problems

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Two Century 21 problems
From: Tom NØJMY <n0jmy@hayseedhamfest.com>
Reply-to: n0jmy@hayseedhamfest.com, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 14 Jun 2009 16:57:53 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Right-O, Frank.  When I was in the truck business we used to use a 
similar Loc-Tite product called "Stud and Bearing Mount".  I fixed a lot 
of things, including certain radio things with it.  But only if I never 
wanted it to come apart again.

As one of my mechanics used to say, "that stuff's harder'n Chinese 
arithmetic!"

73,
Tom

Frank Holladay wrote:
> Be very sure that if you use the purple Loc-Tite that you will never need to 
> remove the knob.  Once that stuff sets up, it is there forever plus three 
> days!
> Frank,
>  K4VMO
> 
> ----- Original Message ----- 
> From: "Tom NØJMY" <n0jmy@hayseedhamfest.com>
> To: "Mike Bryce" <prosolar@sssnet.com>
> Cc: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Sunday, June 14, 2009 3:41 PM
> Subject: Re: [TenTec] Two Century 21 problems
> 
> 
> Got 'er.  Now on to the set-screws.  The missing audio was primarily due
> to one of the little coil leads on the speaker being broken.  Apparently
> it was weak and the loud calibrator vibrations finished her off.
> 
> And, Mike was right, that selectivity switch *was* dirty, making it
> intermittent.  Got that taken care of and we're in business.
> 
> Now for the knobs.
> 
> 73,
> Tom
> 
> Tom NØJMY wrote:
>> Well, we may have multiple problems here.  But I did get the audio
>> back...for now.  I decided to check and see if there was any sidetone.
>>
>> With a dummy load hooked up I tapped the leads from the power set switch
>> together - had power our but no sidetone.  Don't know what possessed me,
>> but I decided to take a listen through the headphones.  Voila, sidetone,
>> and after tickling around a little bit I had some receive audio.
>>
>> So I messed with the selectivity switch again and bingo, full audio!
>>
>> Pull the headphone plug out - silence.
>>
>> So, I guess I'll definitely clean that switch, then go after the
>> headphone-jack/speaker circuit to see what gives.  I'd like to think
>> that it was something as simple as a bad connection at the jack, or even
>> if the loud signal from the calibrator just blew out the speaker. Things
>> are never that simple, though.
>>
>> Then I can try out some of the suggestions on my set-screws.
>>
>> 73,
>> Tom
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>