thay are talking the dsp bw not the transmitte bw
----- Original Message -----
From: "Phil Howlett" <w9xx@hoosierbroadband.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Thursday, June 17, 2010 8:25 PM
Subject: Re: [TenTec] bugs in Orion firmware 2.044A
Same here....No problem. Plays very well. Bad download?
W9XX
On Jun 17, 2010, at 7:49 PM, John Simon wrote:
Just to throw a jinx in the comments, my OII returns to whatever I
had setup
before I turned her off. BW, PWR, etc, same with User 1 and User 2.
I find the 2.044 very similar to 2.039 version.
Could there be a difference within the radio , ie tolerances of
components
differing?
John de VK2XGJ
Stop worrying about Life
You'll never get out of it alive
----- Original Message -----
From: "Steven Kline" <skline4@verizon.net>
To: "Rick Borken" <rickb@cpinternet.com>; "Discussion of Ten-Tec
Equipment"
<tentec@contesting.com>
Sent: Friday, June 18, 2010 4:00 AM
Subject: Re: [TenTec] bugs in Orion firmware 2.044A
Last night I observed a problem somewhat similar to what Rick is
describing.
I noticed that what ever setting the variable BW is reading prior to
shutting the radio off is not the same BW setting that is restored
if you
turn the radio off and then turn it back on. For example if I was
in SSB
mode, with BW set to 3000 and then turn the radio off and then
back on;
after boot-up the BW setting may come up as 2480 or some other
number but
not 3000 where it was at prior to shut down. Same occurs in CW
mode, and
can be replicated.
Maybe related to same problem below. Can anyone else validate the
power
on/off sequence and confirm if their BW setting was restored to
same value
as it was before turning the power off?
Thanks
Steve - W5JK
On Jun 17, 2010, at 8:39 AM, Rick Borken wrote:
Here are three bugs which I have found in the recent 2.044A firmware
update.
I have reported them to Ten-Tec:
The fix "fixed restoration of bandwidth when recalling USER
memory" does
not
work correctly in v 2.044A. It behaves differently than it did in
2.043,
but
it is still incorrect.
When I recall a USER memory, the bandwidth always gets set to
1000 Hz for
CW, 2400 Hz for FSK and 100 Hz for SSB. It
does not reset to the value I tried to store in a USER memory.
When I push the RECALL button and then recall the Factory Default
USER
settings, the resulting screen shows PWR set to 100, and the
value of PWR
is "frozen,"
and cannot be changed in the normal way by highlighting the
value and adjusting it with the MULTI knob.
in v 2.044A, the value of "AGC Hang" is not restored to the
value stored
in
the USER memory when recalling a USER memory.
73, Rick K0XB
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
--------------------------------------------------------------------------------------------
Email Provided by Hoosier Broadband - Indiana's #1 Source for High-Speed
Wireless Internet!
www.hoosierbroadband.com
--------------------------------------------------------------------------------------------
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|