i first cover the adjacent LED bond pads with Aluminum foil token them from
getting hot.
I then heat all of the pins at once using the small heat gun on my Hakko rework
station.
Once all pin bond solder is melted, I snap the board against a safe surface so
as to make the molten solder fling out of the holes.
The encoders always come out easily and the board does not get overheated and
the pads are undamaged.
Gary
> On Apr 8, 2018, at 6:03 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>
> http://tentecwiki.eqth.net/doku.php?id=565enc
>
> On Sun, Apr 8, 2018 at 9:16 PM, Kim Elmore <cw_de_n5op@sbcglobal.net> wrote:
>
>> Can you describe that method? I have an O II that’s showing signs of a
>> dirty switch in the small encoders. I just successfully replaced every
>> electrolytic capacitor in my old TS-930S (about 150 of ‘em) so replacing
>> the coders can’t be a whole lot worse.
>>
>> Kim N5OP
>>
>>
>>
>> "People that make music together cannot be enemies, at least as long as
>> the music lasts." -- Paul Hindemith
>>
>>> On Apr 8, 2018, at 15:51, MadScientist1948 <dukeshifi@comcast.net>
>> wrote:
>>>
>>> I ordered several dozen of them.
>>>
>>> From now forward, if I have to go to the work to replace ONE encoder on
>> any Orion I get through here, I will replace all of them. They are low cost
>> and that is a good preventative repair on Orion’s once the two hour
>> disassembly job is already done!
>>>
>>> I have a pretty good method for getting them off the board easily.
>>>
>>> Gary
>>>
>>>> On Apr 7, 2018, at 6:57 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>>>>
>>>> The S in S0015 means it has a switch.
>>>>
>>>>> On Sat, Apr 7, 2018 at 11:39 PM, Rodney <w3krq@dejazzd.com> wrote:
>>>>>
>>>>> Do the ones from digikey have a switch .
>>>>>
>>>>> -----Original Message----- From: Barry N1EU
>>>>> Sent: Friday, April 06, 2018 12:48 PM
>>>>> To: Wes Attaway (N5WA)
>>>>> Cc: Discussion of Ten-Tec Equipment
>>>>>
>>>>> Subject: Re: [TenTec] orion encoders?
>>>>>
>>>>> No, get the recommended ones from Digi-Key, they're in stock:
>>>>> https://www.digikey.com/product-detail/en/bourns-inc/PEC11L-
>>>>> 4225F-S0015/PEC11L-4225F-S0015-ND/4699180
>>>>>
>>>>> 73, Barry N1EU
>>>>>
>>>>> On Fri, Apr 6, 2018 at 11:16 AM, Wes Attaway (N5WA) <
>>>>> wesattaway@bellsouth.net> wrote:
>>>>>
>>>>> How about these, from Mouser ...
>>>>>>
>>>>>> PEC11L-4015F-S0015
>>>>>>
>>>>>> They have 1200 in stock
>>>>>>
>>>>>> -------------------
>>>>>> Wes Attaway (N5WA)
>>>>>> (318) 393-3289 - Shreveport, LA
>>>>>> Computer/Cellphone Forensics
>>>>>> AttawayForensics.com
>>>>>> -------------------
>>>>>>
>>>>>> -----Original Message-----
>>>>>> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
>> Barry
>>>>>> N1EU
>>>>>> Sent: Friday, April 06, 2018 6:54 AM
>>>>>> To: Discussion of Ten-Tec Equipment
>>>>>> Subject: Re: [TenTec] orion encoders?
>>>>>>
>>>>>> Sorry, the encoders are out of stock at Mouser, so I had to delete
>> that
>>>>>> link. The 20 PPR encoders ARE available but the 15 PPR encoders are
>> more
>>>>>> suitable (but are out of stock). I suggest you try one of the other
>>>>>> vendors (Newark, Allied, etc)
>>>>>>
>>>>>> Barry N1EU
>>>>>>
>>>>>>> On Fri, Apr 6, 2018 at 7:50 AM, Barry N1EU <barry.n1eu@gmail.com>
>> wrote:
>>>>>>>
>>>>>>> Here's a direct link to order 10 encoders for $18.50 from Mouser:
>>>>>>> https://www.mouser.com/ProjectManager/ProjectDetail.
>>>>>>> aspx?AccessID=443fb4d200
>>>>>>>
>>>>>>> Barry N1EU
>>>>>>>
>>>>>>>> On Fri, Apr 6, 2018 at 7:24 AM, Ted Bryant <w4nz@comcast.net>
>> wrote:
>>>>>>>>
>>>>>>>> Here's what I used to replace all six small encoders on my Orion II.
>>>>>> They
>>>>>>>> work very well. I've had no problems with encoders since.
>>>>>>>>
>>>>>>>> From Mouser:
>>>>>>>>
>>>>>>>> 652-PEC11L4225FS0015 PEC11L-4225F-S0015 ENCODER
>>>>>>>>
>>>>>>>> Bought 10 for about $16
>>>>>>>>
>>>>>>>> 73, Ted W4NZ
>>>>>>>>
>>>>>>>>
>>>>>>>> -----Original Message-----
>>>>>>>> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of
>>>>>>>> MadScientist1948
>>>>>>>> Sent: Thursday, April 05, 2018 11:54 PM
>>>>>>>> To: Discussion of Ten-Tec Equipment
>>>>>>>> Subject: [TenTec] orion encoders?
>>>>>>>>
>>>>>>>>
>>>>>>>> Well, I sold off all of my Orion small encoders to help others
>> repair
>>>>>>>> their
>>>>>>>> radios.
>>>>>>>>
>>>>>>>> Now I have an Orion 2 with two bad encoders.
>>>>>>>>
>>>>>>>> Does anyone have any or does any one recall the replacement I had
>> heard
>>>>>> of
>>>>>>>> previously?
>>>>>>>>
>>>>>>>> Gary
>>>>>>>>
>>>>>>>> W0DVN
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> TenTec mailing list
>>>>>>>> TenTec@contesting.com
>>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>> _______________________________________________
>>>>>> TenTec mailing list
>>>>>> TenTec@contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>> ---
>>>>> This email has been checked for viruses by AVG.
>>>>> http://www.avg.com
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|