Rick, I run almost 100% in the assisted category.
Yes, in my more serious efforts, I aggressively use the bandmap. Here's
one example: http://n1eu.com/n1mm/cwso2v.htm (click audio link and listen
as I work both vfoA and vfoB bandmaps simultaneously on my Orion)
In my less serious efforts, I'm more likely to tune the band manually, old
style.
73, Barry N1EU
On Wed, Nov 5, 2014 at 7:17 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de> wrote:
> Well a BandMap is not exactly blind and dumb.
> $1K towards a new radio is already a good start.
>
> Question Barry, do you run assisted or unassisted?
> And the 2nd, have you used the BandMap aggressively?
>
> Before using a BandMap, and running just wire antennas (dipole) and 600w,
> my
> typical score was about 500K.
> The first year using the bandmap it jumped to 800K and the second year to
> 1M+.
> And that without a properly integrated BandMap (lack of OmniRig support).
>
> A BandMap is worth a lot of money to me, but I didn't have to pay for it
> because it is for free to everyone, assuming you have a good contest
> logging
> software already.
>
> 73 - Rick, DJ0IP
> (Nr. Frankfurt am Main)
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Barry
> N1EU
> Sent: Wednesday, November 05, 2014 12:40 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Pan-Adaptor vs. Using BandMap with Ten-Tec
> Transceivers
>
> It's not worth it.
>
> I think you either go "whole hog" with a Flex 6K or go blind, dumb and
> happy
> with a classic radio.
>
> 73, Barry N1EU
>
> On Wed, Nov 5, 2014 at 6:06 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de>
> wrote:
>
> > GM Barry,
> >
> > Tnx for the input. It's a valid point.
> >
> > If he's in the bandmap, I will also know that.
> > If not, you're right, I will go right past him and not know he was there.
> > Perhaps I'll miss him forever, but maybe I'll get him on the next pass.
> >
> > Honestly, I estimate my cost of implementing a good band scope to be
> > about $1000, including the computer stuff I'll have to buy. There was
> > I time I would have just reached into my pocket and pulled out the
> > money, but now that I'm retired, that represents about 2 years of entire
> ham radio budget.
> >
> >
> > I have to weigh this decision against what else I could buy with that
> > money.
> > I can name plenty of other things I don't have and right now and would
> > prefer to spend my money on.
> >
> > A higher priority is a new NAS drive. The old one has been running
> > day and night for 5 years now. I need to replace it before it breaks.
> > That's already a couple hundred gone.
> >
> > Then there's a high power cross-needle watt meter. I also would like
> > a dual-line RF-Ammeter, so that I can measure current on both sides of
> > openwire at the same time. I'd like to buy and try the Ten-Tec
> > RF-Speech Processor, and maybe even buy a headset with mic, just in
> > case I ever go back on my word and do another SSB contest. But for
> > that I would also need a voice memory box. Lots more stuff to spend
> > the money on instead of a bandscope.
> >
> > Agn, good point. One which I hadn't thought about.
> > TNX
> >
> > 73 - Rick, DJ0IP
> > (Nr. Frankfurt am Main)
> >
> >
> > -----Original Message-----
> > From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Barry
> > N1EU
> > Sent: Wednesday, November 05, 2014 11:49 AM
> > To: Discussion of Ten-Tec Equipment
> > Subject: Re: [TenTec] Pan-Adaptor vs. Using BandMap with Ten-Tec
> > Transceivers
> >
> > When you're tuning the band in S&P, you can see in advance when coming
> > to a frequency that the cq'ing station is momentarily listening and
> > you know to pause on the frequency for a second and listen for the
> > station to resume cq'ing rather than possibly tune right by him.
> >
> > 73, Barry N1EU
> >
> > On Wed, Nov 5, 2014 at 9:29 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de>
> > wrote:
> >
> > > I separated this out from the "Future Radio" thread.
> > > Both of these features are here already today.
> > >
> > > I AM STILL TRYING TO UNDERSTAND HOW THE BANDSCOPE (or Pan-Adaptor)
> > > WILL HELP "ME" in "my way" of working DX contests.
> > > I know it helps for other things, but how will it improve my contest
> > score?
> > >
> > > For this thread, I hope you guys will focus on my specific problem
> > > (which may very well be my slowness to understand), rather than try
> > > to sell me the general benefits of using a Pan-Adapter for all sorts
> > > of other applications.
> > >
> > > First, I understand that people have different interests and we all
> > > like to play with technology. I understand how it is fun and
> > > helpful to
> > others.
> > > But for my needs?
> > >
> > > My main interest in operating are:
> > >
> > > .1.Working DX Contests (and only those Contests),
> > >
> > > .2.Working DX-peditions (especially the ones I sponsor),
> > >
> > > .3.And rag chewing on 80 in SSB.
> > >
> > > PLEASE FOCUS ONLY ON #1 FOR THIS THREAD. TNX.
> > >
> > >
> > > I am still trying to understand how a pan-adaptor or bandscope would
> > > help me in a DX contest. that is, help enough that it would warrant
> > > the time, effort and cost necessary to add this feature to my Eagle.
> > > It will take some hardware modification to "my" Eagle to do that. I
> > > have an original version.
> > >
> > > Remember, every second spent watching that device (or anything else)
> > > is one less second I could be making a QSO, and a QSO usually takes
> > > just 5 seconds.
> > >
> > > So far nothing I have read has convinced me that it would be worth
> > > the effort (with reference to improving DX Contest scores).
> > >
> > > Clearly it would be a big aid in chasing the DX-peditions.
> > > I understand that.
> > > It might even be an aid in my 80m rag chewing because it would help
> > > me identify who is splattering up and down the band.
> > >
> > > BUT WHERE IS THE BENEFIT IN DX CONTESTING ?
> > > (since I am already making full use of the BandMap with external
> > > spots and skimmer)?
> > >
> > > The only thing anyone has suggested so far which I fully accept is,
> > > when you decide it's time to stop S&P and call CQ, it helps locate a
> > > clear frequency.
> > >
> > > In a 48 hour CW contest, I might pause S&P and call CQ for a while,
> > > but I only do that 2 or 3 times each night.
> > > I don't do it in an SSB contest at all.
> > >
> > > I don't call CQ during the day because my signal is not strong
> > > enough to hold a frequency. I have never needed longer than one
> > > minute to find a frequency (160/80/40) and begin working.
> > >
> > >
> > > FIRST THE BANDMAP:
> > >
> > > When I am operating S&P, my BandMap which is fed by packet posts and
> > > skimmers, shows me:
> > >
> > > .1.Call Sign and frequency of "Run" stations who are calling CQ
> > >
> > > .2. Whether or not I have already worked the stn.
> > >
> > > .3. If the station is a new Country, new Zone, or Both
> > >
> > > .4. All stations, including those that I cannot even hear because
> > > propagation is not favorable to my QTH
> > >
> > > Of course #4 is the "gotcha" here with using the BandMap. Room for
> > > improvement.
> > >
> > > But my gut feeling is, less than 25 of the posts I see are for
> > > stations which I cannot hear.
> > > And even if they are, a few hours later propagation changes enough
> > > that they now become "live" for me.
> > > So even though I can't hear (i.e. K3LR), I know not to call CQ on
> > > that frequency.
> > >
> > > The BandMap is totally free for me, because my contest logging
> > > software incorporates this feature.
> > > My score has sky-rocketed upwards since I began using the BandMap in
> > > contests.
> > > This helped far more than using manual packet spots.
> > >
> > >
> > > SECOND THE BANDSCOPE:
> > >
> > > Question: is there a difference between a bandscope and a pan-adaptor?
> > >
> > > BENEFITS:
> > >
> > > .1. Helps identify clear spots when I'm looking for a frequency to
> > > call
> > CQ.
> > >
> > > GOOD POINT.
> > > But weak point for my type of operation because I rarely do this.
> > > I don't think anyone does it a lot. If you are strong enough to
> > > hold a frequency, you just stay there. Otherwise you do S&P.
> > >
> > > .2. Lets me know what is going on around my frequency.
> > > Why should I care? My radio has excellent filters and in a contest,
> > > I must go to cluttered frequency to work the rare multipliers,
> > > regardless of what's going on around it.
> > >
> > > When working S&P, I usually don't stay on one frequency longer than
> > > 15 or
> > > 20
> > > seconds, then I move on.
> > >
> > > If I'm calling CQ, I still don't care. If people are calling me and
> > > I can work them, I'm on a good frequency.
> > > The entire band is full of signals. Otherwise I'm on another band.
> > >
> > > If I happened to settle down on the frequency of a rare DX station,
> > > plenty of people will let me know; I send a "SRI" and QSY.
> > >
> > > Besides, the Band-Scope won't tell me that I have settled on a DX
> > > station's frequency, but the BandMap will!
> > >
> > > .3.I can see when other bands are open.
> > > GOOD POINT. Actually EXCELLENT POINT.
> > >
> > > The packet spots show me this too, to some extent. Certainly not as
> > > well as the band-scope would.
> > > For stations who have full automation, and can double-click to
> > > change bands, this might be a lot more benefit.
> > > I need too long to change bands because I have a manually tuned amp,
> > > and manual antenna switch, and manual matchbox.
> > > The up side to "manual" is, it usually doesn't break.
> > > After each major contest, our BCC reflector is full of people
> > > complaining about automated stuff that broke.
> > >
> > > My work-around: I change bands and use the second VFO to scan the
> > > band at a rapid rate in 1kHz steps. I just listen to bursts
> > > (without stopping). If the band is full, I consider changing. It
> > > takes a few minutes for the BandMap to populate, so it is not any
> > > help for this operation. This process costs me about 60 to 90 seconds.
> > >
> > > .4. I don't know any others. Other than it might be fun; but fun
> > > doesn't improve my contest score.
> > > HELP ME OUT HERE PLEASE: _______________________
> > >
> > > DOWNSIDE OF BANDSCOPE FOR ME:
> > >
> > > .1.Cost. I would not only incur the cost for whatever hardware is
> > > needed, I would have to purchase a new computer. It was suggested
> > > not to use a laptop. This means I would need a computer, keyboard,
> > > and monitor. However my shack is tiny and already over-crowded,
> > > which is one of the reasons I use a laptop.
> > >
> > > Doing this is not out of the question, but at the end of the day, is
> > > it really going to improve my score significantly? I can't see how.
> > >
> > > It's also very difficult to find a good US-English keyboard over here.
> > > I'd probably have to pay shipping from the states.
> > > Perhaps Scott (W4PA) could bring me one when he comes to visit next
> > summer.
> > >
> > > .2..Labor: My early model Eagle motherboard does not have the
> > > connection to run the IF out. I don't mean the jack on the back, I
> > > mean the connection on the printed circuit board. I would have to
> > > take a soldering iron to it. I am technically competent, but with
> > > poor eyesight. If I do this, there is some risk that I might break
> > > something. A round trip back to the factory costs $300.
> > >
> > > Again, please keep this thread focused on "how a Band-Scope can help
> > > in DX-Contesting", and not break out in a general discussion of the
> > > benefits of a band-scope. I understand that there are benefits in
> > > other aspects of the hobby.
> > >
> > > THANK YOU.
> > >
> > > 73 - Rick, DJ0IP
> > > (Nr. Frankfurt am Main)
> > >
> > >
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|