Hello Jerry,
"building something without experimenting is just solder
practice" I would change that a little.... Building a Kit without at least
one Engineering Change, is just solder practice. When I was young, it was
easy to pick on Bald Headed old men who needed a magnifying glass to see
the schematic. When I looked into the mirror this morning, it seems that
time sneaked up on me and I became one. The good part is that. Over the
years, I became the old Elmer that we used to ask all those questions. Life
is a good thing. Enjoy it every day...
Wade/KJ4WS
On Wed, Jun 4, 2014 at 8:42 PM, Jerry Haigwood <jerry@w5jh.net> wrote:
> Barry,
> Congratulations on winning the QRPTTF. You had an impressive score!
>
> Jerry W5JH
> "building something without experimenting is just solder practice"
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Barry
> N1EU
> Sent: Wednesday, June 04, 2014 11:35 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] More Junk....
>
> I think it has dual DACs and two hardware DDC receivers.
>
> Barry N1EU
>
>
> On Wed, Jun 4, 2014 at 2:49 PM, Duane Calvin <ac5aa1@gmail.com> wrote:
>
> > And, it appears to have only one slice (receiver) plus RIT/XIT. Hmm,
> must
> > be more to it than that with all the antenna connectors.
> >
> > 73, Duane
> >
> > Duane Calvin, AC5AA
> > Austin, Texas
> > www.ac5aa.com
> >
> >
> >
> >
> > -----Original Message-----
> > From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Tom
> > Pennebaker
> > Sent: Wednesday, June 04, 2014 9:37 AM
> > To: TenTec@contesting.com
> > Subject: [TenTec] More Junk....
> >
> > If you will look closely at the rear picture, you can detect poor
> > quality. I bought a Russian CW paddle years ago, it is pure JUNK!!! The
> > rear photo shows the possibility of junk. Where are you going to get it
> > serviced when it fails? A Rolls Royce isn't any good if you can't get it
> > seviced.....
> > CW IT'S STILL MAGIC.... Tom N4RS
> >
> > > On Jun 4, 2014, at 8:20, Barry N1EU<barry.n1eu@gmail.com> wrote:
> > >
> > > I know we've recently discussed SDRs on the reflector so please excuse
> > this
> > > off-topic post. There's a nice looking SDR in the works out of Russia
> > with
> > > its own front panel. It actually has an embedded i5 processor. It is
> > > going to be introduced at Friedrichshafen. There have been quite a few
> > > youtube videos of it in prototype phase over the past year or so.
> Here's
> > a
> > > photo:http://sunsdr.com/images/fbfiles/images/SunSDR2_MB1_1_.jpg
> > >
> > > I don't know anything else about it.
> > >
> > > 73, Barry N1EU
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|
