I must have put the wrong address in because non of my reply's to anyone have
shown up here oh well. Good ideas Frank I've got chokes and caps every where in
my design hi hi, but I might just toss the idea out for running power cable's
out to each preamp not as clean but easier. I have 110v power real close to
each antenna so getting power to each antenna isn't a real problem and voltage
drop won't be a problem either.
So far this project has been lots of fun I used W7IUV preamp design with my
own pc boards they work great best amps I've used before I just need to finish
the rest of the package and see how the whole system works.
73 Dave
________________________________
From: "donovanf@starpower.net" <donovanf@starpower.net>
To: topband@contesting.com
Sent: Sunday, January 8, 2012 8:38 AM
Subject: Re: Topband: Bias Tee question
Dave,
Use a well over rated DC blocking capacitor, this is not an application to save
a few pennies by using a marginally rated capacitor.
You should also use a choke to ground with a high current rating to protect
your receiver if the capacitor shorts out. A choke wound with #18 wire on a
ferrite core will guarantee that your receiver won't be trashed if the
capacitor fails.
Its a good idea to place capacitors in series with all three ports of a
"magic-T" 3 dB splitter. The ferrite cores in commercially made splitters are
very small, if even a small amount of 60 Hz AC current flows through the core
it will saturate causing intermod problems.
In a multi-operator station, a bandpass filter should be installed to protect
the splitter from strong signal saturation, also resulting in intermod problems.
You can avoid splitter intermod problems by building your own splitter with
large ferrite cores, but you can usually avoid that by using bandpass filters
and capacitors to protect the splitter from saturation.
73
Frank
W3LPL
---- Original message ----
>Date: Sat, 7 Jan 2012 15:08:48 -0500
>From: "ZR" <zr@jeremy.mv.com>
>Subject: Re: Topband: Bias Tee question
>To: "Dave Kirk" <w6mqi@yahoo.com>, <topband@contesting.com>
>
>It never hurts to have a DC block when Murphy is around.
>
>Carl
>KM1H
>
>
>----- Original Message -----
>From: "Dave Kirk" <w6mqi@yahoo.com>
>To: <topband@contesting.com>
>Sent: Saturday, January 07, 2012 2:42 PM
>Subject: Topband: Bias Tee question
>
>
>> I’m designing a multi element receive array which
>> incorporates the usual 0 deg hybrid
>> combiner, 180 deg phase inverter, and 2:1 transformer. I’m going to use
>> pre
>> amps on the antenna elements and need to supply 12 volts to them via the
>> feed
>> lines through a bias tee. My question is do I need to worry about 12v
>> being fed
>> back through the combiner, phase inverter, or 2:1 transformer to my
>> receiver even
>> though their not physically connected or should I put .01 cap on the feed
>> line going the my receiver for
>> safety.
>>
>>
>> Thanks Dave.
>> _______________________________________________
>> UR RST IS ... ... ..9 QSB QSB - hw? BK
>>
>> -----
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 10.0.1416 / Virus Database: 2109/4128 - Release Date: 01/07/12
>>
>
>_______________________________________________
>UR RST IS ... ... ..9 QSB QSB - hw? BK
_______________________________________________
UR RST IS ... ... ..9 QSB QSB - hw? BK
_______________________________________________
UR RST IS ... ... ..9 QSB QSB - hw? BK
|