Towertalk
[Top] [All Lists]

Re: [TowerTalk] Fw: Cable pulling

To: <TowerTalk@contesting.com>
Subject: Re: [TowerTalk] Fw: Cable pulling
From: "Eugene Jensen" <eugenejensen@nyc.rr.com>
Date: Sun, 6 May 2012 19:08:01 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
This is an old Electrician trick. Take a small plastic  wrapper about the
size of a cigarette pack hint hint tie a light fishing line to the wrapper
and use a shop vac and put the hose wrapped in rags to make a suction in one
end and when you have it set away you go.   You suck up the wrapper and
fishing line into the shop vac. I used the trick here with a  150 feet 4
inch line that was installed when the house was built.  73 Gene K2QWD

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Bob Gibson
Sent: Sunday, May 06, 2012 6:47 PM
To: towertalk@contesting.com
Subject: [TowerTalk] Fw: Cable pulling

How long are the sections? Why not just lay the sections out and run the
cables into each section one at a time..that's what I did for 350ft run..Bob
Bob Gibson W5RG

----- Forwarded Message -----
From: David Aslin <david@aslinvc.com>
To: towertalk@contesting.com
Sent: Sunday, May 6, 2012 4:48 PM
Subject: [TowerTalk] Cable pulling

Gerald's note prompts me to ask a related question:
What techniques are folks using for the first pull through a conduit?
Background: Like Gerald, I plan to have a 400ft+ run of 4 inch corrugated
irrigation tubing.  A 400ft fish tape would be hard to find/expensive, but I
need to get a pull rope through the conduit before I can do the first cable
pull (LDF5-50)  How?

73
David G3WGN  WJ6O

------------------------------
Date: Sun, 6 May 2012 15:13:42 -0300
From: "VE1DT-Towertalk" <gboutin@seaside.ns.ca>
Subject: [TowerTalk] Wire Soap - How Much?
To: <towertalk@contesting.com>
Message-ID: <001801cd2bb3$f96e2ce0$ec4a86a0$@seaside.ns.ca>
Content-Type: text/plain;    charset="us-ascii"

I've no experience in running cables through conduit, but I do know that I
want to use a cable lube. I can get Klein #15028 1 quart bottles locally,
but I don't know how much I will need. Also, I know I don't want to run out
part way. In browsing through the archives, the answer I keep seeing is
"lots".

In my case, I am using 4" diameter corrugated irrigation tubing for a couple
of LMR600 cables, a couple rotator cables and a few CAT5 cables.
Total
length is 400 feet. Worst case would be the volume of the conduit.
Using
the formula,    pi *r^2 *length    tells me about 30 gallons. I am not
planning on doing that.

Polywater  http://www.youtube.com/watch?v=kr87VQcJeK8 ; says to use this
formula for PolywaterJ: Gallons = 0.0015 * Diameter(inches) * Length(feet).
This comes out to 2.4 gallons. Using 1 quart bottles, this comes to about
$150 here. Grainger also sells larger 1 gallon containers of 3M WL lube at
about the same price as two of the Klein one quart squeeze bottles.

Does 3 gallons sound about right?

--
Gerald Boutin, VE1DT

********************************
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>