Towertalk
[Top] [All Lists]

[TowerTalk] Tuning the K8UR-Style 4-Square

To: <towertalk@contesting.com>
Subject: [TowerTalk] Tuning the K8UR-Style 4-Square
From: philk5pc@tyler.net (Phil Clements)
Date: Mon, 27 Sep 1999 14:38:32 -0500
Thanks for the input, Dave.
I have an idea that my broader bandwidth is due to the
fact that my tower is insulated from the 60 foot point on up.
Someone could model this and see.

(((73)))
Phil, K5PC



> Phil:
>
> I have a K8UR configuration 4 square on 80 mtrs which hangs off the 120' guy
> ring on my rotating tower.  Based on my own experience, I'm suspicious of
> your SWR readings.  The antenna simply cannot be that flat over a 100 KHz
> bandwidth.
>
> Also, when I was building mine I was anticipating an upward shift in
> resonance due to the mutual coupling of the four antennas.  On the K8UR
> configuration, this does not happen. . . so you don't want to follow the
> general rule of thumb of starting out with antennas that are low in
> frequency.  I cut my dipoles by the formula for 3.490 thinking the array
> would shift upward by 5% or so.  I installed the first one and it was
> resonant at 3.490 per the formula.  I added the other three. . . the
> resonant frequency of the array didn't change (measuring resonance as the
> minimum power dumped to the dummy load).  I'm getting 2-3 watts into the
> dummy load with about 90 watts delivered to the Comtek box. . . but
> certainly not over a 100 kHz window.  I'd have to say something else is
> influencing your readings.
>
> 73 and good lowband DX this season to all. . . Dave
> W0FLS
> -----Original Message-----
> From: Phil Clements <philk5pc@tyler.net>
> To: towertalk@contesting.com <towertalk@contesting.com>
To: <towertalk@contesting.com>
> Date: Monday, September 27, 1999 12:50 PM
> Subject: [TowerTalk] Tuning the K8UR-Style 4-Square
>
>
> >
> >On page 11-79 of ON4UN's 1999 book, Mike, K4PI
> >uses vacuum relays to switch about 6 feet of wire on
> >each of his 4 dipoles at the ground level to QSY his
> >K8UR-style 4-square from the SSB DX window to the
> >CW DX window on 80m.
> >
> >Since my version was resonant when installed at 3622 khz,
> >I cut 5 feet off the bottom end of each dipole to QSY the
> >array to  3770 khz. My  "window of resonance" on this array
> >is 100 khz. IOW, the power to the dummy load on the Comtek
> >box is zero from 3713 to 3813 khz.
> >
> >All this sounds really good, but could this be good VSWR for
> >all the wrong reasons? I now no longer have  4 symetrical dipoles,
> >but 4 off-center-fed dipoles. What has this done to the pattern
> >and or the Comtek box? Has anyone run any modeling on a
> >situation similiar to this one? Please share any of your experiences.
> >
> >(((73)))
> >Phil, K5PC
> >
> >
> >
> >
> >--
> >FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
> >Submissions:              towertalk@contesting.com
> >Administrative requests:  towertalk-REQUEST@contesting.com
> >Problems:                 owner-towertalk@contesting.com
> >Search:                   http://www.contesting.com/km9p/search.htm
> >
> >
>



--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>