Thanks for the info, Doug. Care to share the info on the mod to the keyway?
Al
N6TA
----- Original Message -----
From: Doug Renwick
To: 'Jack Parker' , john@kk9a.com
Cc: al n6ta , TowerTalk@contesting.com
Sent: Tue, 10 Nov 2009 17:58:04 +0000 (UTC)
Subject: RE: [TowerTalk] HDR3-00 on the AS455G shelf?
The keyways (2) are the Achilles heel of the HDR-300. I haven't seen
the new redesigned shaft but I redesigned my keyways and it has solved
the problem.
Doug
I'll run the race and I will never be the same again.
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Jack Parker
Sent: November 10, 2009 11:48 AM
To: john@kk9a.com
Cc: al_n6ta@comcast.net; TowerTalk@contesting.com
Subject: Re: [TowerTalk] HDR3-00 on the AS455G shelf?
I am curious as to what antenna configuration wore out the keyway. I
have 3
HDR-300's (one with a control box issue that needs to be resolved) but
have
never had one in service. I have a KT-34XA (with some M-Squared
upgrades)
that may go on one '300 and at least a long-boom (40+ foot) six meter
yagi
and a 3.2-wavelength 2-meter yagi on the other. Are either of those
configurations too much for the '300?
Yes, I am in a wind-prone area of northern Nevada where 30-40 mph winds,
with gusting above 50 mph, are not uncommon.
73,
On Tue, Nov 10, 2009 at 6:05 AM, john@kk9a.com
wrote:
> About two decades ago I had two Hy-Gain HDR-300 rotators and I don't
recall
> any bolt hole issues, however I do recall a lot of problems. The
biggest
> issue was with the keyway on the shaft wearing out and needing yearly
> replacement. If the T2X is not up to your task, I doubt that the
HDR-300
> will be.
>
> John KK9A
>
>
>
> To: TowerTalk
> Subject: [TowerTalk] HDR3-00 on the AS455G shelf?
> From: al_n6ta@comcast.net
> Date: Tue, 10 Nov 2009 05:25:10 +0000 (UTC)
>
>
> My T2X is not quite up to the task anymore so I thought I might
replace it
> with
> an old HDR-300 that I have had in storage for 25 years. Anyone know
if it
> will
> fit the AS455G accessory shelf that suports the T2X currently? If it
will
> fit,
> does anyone hae a guide as to where to poke the new holes for the 300?
I
> just
> cannot find a dimensioned drawing for the shelf.
>
> Thanks, all!
>
> Al
> N6TA
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
--
Jack, W6NF
Silver Springs, NV
DM09ji
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|