Towertalk
[Top] [All Lists]

(Fwd) Re: [TowerTalk] An Engineering Question

To: <towertalk@contesting.com>
Subject: (Fwd) Re: [TowerTalk] An Engineering Question
From: ke4rna@Traveller.COM (Donnie Murray (KE4RNA))
Date: Tue, 27 May 1997 22:35:13 +0000
------- Forwarded Message Follows -------
From:          Self <Single-user mode>
To:            David Clemons <dave@egh.com>
Subject:       Re: [TowerTalk] An Engineering Question
Reply-to:      ke4rna@traveller.com
To: <towertalk@contesting.com>
Date:          Tue, 27 May 1997 21:00:46

To: <towertalk@contesting.com>
> Date:          Tue, 27 May 1997 16:42:43 -0400 (EDT)
> From:          David Clemons <dave@egh.com>
> To:            towertalk@contesting.com
> Subject:       [TowerTalk] An Engineering Question

> Hi,
> 
>         I have a question concerning guy wire anchor placement.  I have
> two towers (one is 83 feet of Rohn 25 with a Hygain 155BA and 105BA, the
> other is 99 feet of Rohn 45 with Cushcraft 204-CD and 402-CD.)  A recent
> edition of the ARRL handbook says that the anchor distance should be
> between 60% and 80% of the tower height.  I have two anchors on each leg,
> with the lower two sets of guys on the inside anchor and the highest guy
> alone on the outside anchor.
> 
>         Now the problem - the 13 acres of property behind me was bought
> last year and the new owners are putting up horse corrals for their
> boarding/training business.  We recently discovered that four of my guy
> anchors (both anchors on one leg of each tower) are actually on their
> property.  They have been nice enough to tell me it's ok, but two of them
> actually fall inside one of the corrals and I think it best to get them
> out of there.  I am not going to move the towers, so that means I have to
> put the anchors closer (the outer ones by 12 feet or so) and also
> probably shorten the towers somewhat.
> 
>         The underlying question really is "how much can I cheat on the
> angle of the guy wires?".  Now there are those among you who will
> correctly tell me that any cheating is dangerous, and I understand that
> concept.  However, I am also aware that there is a different amount of
> danger associated with the anchor at 59% of the tower height than at 39%
> or 29%.  Also, my use of two anchors takes some strain off the anchor for
> the top guys - thus making the issue of the strain on the wire and tower
> legs more likely to be the critical problem.  The guy wire is 1/4 EHS,
> which I believe is rated for 6600 pounds.  The wires are broken up with
> insulators, and some of the wires are fastened with deadends while other
> connections are made using 3 cable clamps on each side.  (If it mattered,
> I could replace all cable clamps with deadends.)
> 
>         Does anyone have any experience or idea of the reliability of an
> installation with the top anchor at 50% of the tower height?  How about
> as little as 40% (about 68% angle to the ground)?
> 
> 73, Dave Clemons K1VUT
> 
Dave, what's the possibility of moving the anchor point a couple of 
feet inside the property line and installing an anchor tall enough to 
maintain the same guy angle?
73/DX,
DONNIE, KE4RNA

--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com

<Prev in Thread] Current Thread [Next in Thread>
  • (Fwd) Re: [TowerTalk] An Engineering Question, Donnie Murray (KE4RNA) <=