At least my T2X manual says 2 1/16”. It must be right because I use 1/32” shims
with my 2” mast and all is perfect.
Now for an embarrassing admission: I was ignorant of this for nearly 20 years
and couldn’t understand why my relatively modest antenna load would regularly
chew up my rotator, nor did I understand why, no matter what I did, the rotator
would sound like it was binding as it rotated. Once I realized my foolishness,
I added the shim and, just like magic, I’ve had no more problems.
Kim N5OP
"People that make music together cannot be enemies, at least as long as the
music lasts." -- Paul Hindemith
> On Dec 16, 2018, at 11:32, Bob K6UJ <k6uj@pacbell.net> wrote:
>
> l looked it up in the manual. The T2X manual says maximum mast diameter is 2
> 1/16"
> 73,BobK6UJ
>
>
>
>
>
> On Sunday, December 16, 2018, 5:29:21 AM PST, Julio Peralta
> <jperalta4@verizon.net> wrote:
>
> I believe the maximum mast size a TX2 rotor will accept is 2 1/16" not 2 1/8".
>
> Julio, W4HY
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of
> FERNANDO MUGUERZA VIDEGARAY
> Sent: Sunday, December 16, 2018 1:07 AM
> To: towertalk@contesting.com
> Subject: [TowerTalk] Fwd: MA40 and T2X rotor off center
>
> I checked in one spec of the T2X rotor and says can drive pipes up to 2-1/8”,
> so the shims should be 1/16” each for a 2” pipe.
> Also check if rotor base is centered on the tower’s base.
> Fernando,XE2FL
>
> Fernando José Muguerza,XE2FL
> Cel. 81.1589.2930
> Email. Fernandojmuguerza@gmail.com
> Email. xe2fl.kf5mn@gmail.com
>
> Enviado desde mi iPhone
>
> Inicio del mensaje reenviado:
>
>> De: FERNANDO MUGUERZA VIDEGARAY <xe2fl.kf5mn@gmail.com>
>> Fecha: 15 de diciembre de 2018, 23:46:45 GMT-6
>> Para: towertalk-owner@contesting.com
>> Asunto: MA40 and T2X rotor off center
>>
>> I think the reason for the wooble of the rotor output is because the rotor
>> is capable of turning Antenna’s pipes up to a list 2-3/8” in diameter,if one
>> uses 2” pipes,since one of the grips is fixed with the base of the rotor and
>> the other is movable to clamp,the shaft will be off center,unless you
>> shim(3/16”) both sides to make to be centered in this case!
>> Fernando,XE2FL
>>
>>
>> Fernando José Muguerza,XE2FL
>> Cel. 81.1589.2930
>> Email. Fernandojmuguerza@gmail.com
>> Email. xe2fl.kf5mn@gmail.com
>>
>> Enviado desde mi iPhone
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|