That link I gave was for white. And what are the rf characteristics of
electric fence fiberglass anyway?
David Robbins K1TTT
e-mail: mailto:k1ttt@arrl.net
web: http://www.k1ttt.net
AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
> -----Original Message-----
> From: Roger (K8RI) [mailto:K8RI-on-TowerTalk@tm.net]
> Sent: Saturday, October 10, 2009 07:15
> To: K1TTT
> Cc: towertalk@contesting.com
> Subject: Re: [TowerTalk] Insulators
>
>
>
> K1TTT wrote:
> > Just remember, you get what you pay for... and if a material isn't
> designed
> > for a specific job then it may not do a very good job at it. in my
> > experience electric fence post material degrades pretty quickly in the
> > sun/rain, after only a year or two the whole surface is nothing but
> loose
> > fibers. So if nothing else you might want to consider some uv
> protective
> > paint on it.
> >
> > By comparison, this material is a bit more expensive ($39.54/5'), but
> comes
> > with known size tolerance, tensile strength specs, and statements about
> > environmental performance. http://www.mcmaster.com/#8543k11/=3zm45w
> > And could probably be on your doorstep Monday or Tuesday.
> >
> But what are it's electrical characteristics and particularly at RF,
> particularly as it's black?
>
> 73
>
> Roger (K8RI)
> >
> > David Robbins K1TTT
> > e-mail: mailto:k1ttt@arrl.net
> > web: http://www.k1ttt.net
> > AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
> >
> >
> >
> >> -----Original Message-----
> >> From: n8de@thepoint.net [mailto:n8de@thepoint.net]
> >> Sent: Friday, October 09, 2009 20:44
> >> To: towertalk@contesting.com
> >> Subject: [TowerTalk] Insulators
> >>
> >> FYI:
> >>
> >> I discovered a new source for insulator material that I will be using
> >> on my 80m tower verticals.
> >>
> >> At the local 'feed store', I found 1+1/4" fiberglass ROD with a few
> >> small pre-drilled holes ... it's designed to be used as an electric
> >> fence post. The rod is VERY STRONG and should hold up quite well.
> >>
> >> The cost for a 6' rod is about $6 .... quite inexpensive. Cutting it
> >> into 6+" lengths is quite easy.
> >>
> >> CAUTION:
> >>
> >> When handling this item, WEAR GLOVES as the fiberglass is RAW and will
> >> leave microfibers in your SKIN.
> >>
> >> When CUTTING it or DRILLING it ... wear EYE PROTECTION. You won't
> >> like the effect should any 'flakes' get in your eyes.
> >>
> >> Tower/antennas going up next week .. .FINALLY.
> >>
> >> Don
> >> N8DE
> >>
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
> >
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|