Towertalk
[Top] [All Lists]

Re: [TowerTalk] Emotator 1105MS Rotator & Controller

To: 'Bob W5RN' <rj.newton.w5rn@verizon.net>, "towertalk@contesting.com" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Emotator 1105MS Rotator & Controller
From: Al Kozakiewicz <akozak@hourglass.com>
Date: Wed, 26 Oct 2011 21:09:13 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Two suggestions:

1. Matte finish transparency film.
2. Clear transparency film and coat the unprinted side with a matte finish 
lacqyer, e.g. Krylon.

Al
AB2ZY

-----Original Message-----
From: towertalk-bounces@contesting.com 
[mailto:towertalk-bounces@contesting.com] On Behalf Of Bob W5RN
Sent: Wednesday, October 26, 2011 7:07 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Emotator 1105MS Rotator & Controller

Try a scrapbooking supply store for vellum paper or another source would be a 
drafting supply store.

73 Bob
W5RN

On 10/26/2011 12:02 PM, Roger Parsons wrote:
> Thanks Don
>
> I could only get onionskin paper on a pad rather than for a printer but I 
> tried it anyway. It printed OK, and is significantly better than normal 
> printer paper, but is still quite grainy/papery with the back lighting.
>
> So I'm still looking.
>
> 73 Roger
> VE3ZI
>
>
>
> ________________________________
> From: "n8de@thepoint.net"<n8de@thepoint.net>
> To: Roger Parsons<ve3zi@rac.ca>; Roger Parsons<ve3zi@yahoo.com>
> Cc: "towertalk@contesting.com"<towertalk@contesting.com>
> Sent: Monday, 24 October 2011, 15:30
> Subject: Re: [TowerTalk] Emotator 1105MS Rotator&  Controller
>
> I would try 'onion skin' paper, or very translucent paper which could be made 
> even LESS opaque by rubbing it with OIL.
> 73
> Don
> N8DE
>
>
> Quoting Roger Parsons<ve3zi@yahoo.com>:
>
>> A while ago my controller stopped indicating the antenna direction,  
>> although everything was OK otherwise. Significant messing around  later I 
>> found that a drive belt in the controller had perished. To  my amazement I 
>> found a source of the correct belt and now it works  fine again.
>>
>> However:
>>
>> The direction indication was a printed translucent sheet held  between two 
>> transparent pieces of polycarbonate. Disassembling the  unit to fit the new 
>> belt made the translucent sheet fall apart - it  was after all at least 20 
>> years old. I was able to draw a  replacement sheet pretty much exactly as 
>> the original, but I can't  find the proper material to print it on. If I use 
>> a transparency it  is much too light and the works of the controller are 
>> clearly  visible though it. If I use paper, the back illumination emphasises 
>>  the grain in the paper and it looks really amateurish.
>>
>> Any suggestions for the best material to use? I use an inkjet  printer, but 
>> if laser is necessary I could take it to a shop for  printout. Thanks for 
>> any help.
>>
>>
>> 73 Roger
>> VE3ZI
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>