(begin freebie plug)
I have just finished a paper about mast loading and mast strength for the
Central States VHF/UHF meeting in Minneapolis around the end of July. I
won't be able to present it due to a previous committment, but it will be
in the Proceedings which you may be able to order. The Proceedings help pay
for the meeting and I don't get a cent so please contact them. I did this
as a service. I also get into rotor side load calculation and calculating
the bending on a Rohn 25G hower that is house bracketed, so hopefully
people will find it useful for preliminary analysis.
(end of freebie plug)
While water pipe is not the preferred material for masts (it is soft) I
know people are going to do it, so I included a table of allowed maximum
bending moments based on an assumed 36,000 PSI yield bending stress. I am
basing the assumed yield stress on a comparison of chemical composition of
the ASTM standard for galvanized pipe and other similar steel compositions
in the American Society for Metals Handbooks.
The governing equations for calculating have been published in several
books and reviewed here in the last month.
Anyway the short answer to your question for 2 1/2" SCH 40 is 3192 ft.lbs.
of bending load, assuming you know the pedigree on the steel meets ASTM
standards. If you don't know, then use 27,000 psi and 3/4 of the 3192, or
2400 ft.lbs.
BTW a 1 1/2" SCH 40 mast (1.900" OD) comes out with 979 ft.lbs. assuming
36,000PSI yield, or 734 ft.lbs if you go with 27,000 PSI yield strength. So
in this case bigger is better.
I don't know your location or tower height or anticipated antennas so can't
make any other comments, other than to make sure you put a drain hole in
the bottom of the mast when you put in the insert, and probably a cap on
top to keep birdy do-do from plugging the drain hole. (Actually saw a
freeze break in a tower leg because of that stuff!)
Good luck, and have a local engineer check out your material and
installation details.
de n0yvy Steven H. Sawyers PE - ARRL Volunteer Consulting Engineer
disclaimer: I and my company agree on at least one thing: My opinions are
my own.
______________________________ Reply Separator _________________________________
Subject: Big, heavy mast
Author: K7LXC@aol.com at ccmgw1
To: <towertalk@contesting.com>
Date: 6/19/96 12:07 AM
In a message dated 96-06-18 21:08:57 EDT, you write:
<< Forwarded Message:
Subj: Big, heavy mast
To: <towertalk@contesting.com>
Date: 96-06-18 11:19:13 EDT
From: sbookout@mail1.mnsinc.com (Steve Bookout)
To: k7lxc@contesting.com
Hi Steve.
Could you please send this out over the tower reflector. My mail handler
can not, for some reason, cope with the reflectors. Keeps sending them back
to me as undeliverable. I would appreciate it. 73 Steve, NJ4F
*************************************************************
*************
Howdy all.
How strong is strong?
I have had a 2 1/2" schedule 80, 21 foot long piece of pipe stored for years
hoping someday to use it for a mast. I measures just under 3" OD and weighs
166 lbs. Just standard schedule 80 galvanized pipe. A real beast. I
figured on machining down a piece of stock to fit in the end and to fit in
the tailtwister. Figured I would pin it in place to hold it all together.
That is, pin it in the pipe not the rotator. I have a pair of the tb-4's
and planned on using both in this application like I do the tb-3 with
smaller stuff. Makes it real handy when working on rotator. I usually keep
about 6-7 feet of the mast in the tower.
Although I have hefted long masts over the top of a tower in the past, I
think I will "build" this one into the tower from the beginning. Put two
sections together with the pipe inside and do the 'ol Iwo Jima trick.
Unless, of course, there is a better way to get it done with the Rohn 45.
For clarity, I'm really not a blivet when it comes to this stuff. I hve a
ton of practical applications experience with this kind of stuff and tend to
be conservative in my approach to things. I just thougt this would be a
good follow-on to the thread that is currently being 'spun'.
Any comments on suitability as a mast, loading, installing, etc.
73, Steve, NJ4F
------------------------------------------
******* DX4WIN ********
Windows logging software for the DX'er.
"..the way logging programs should be."
Visit our Homepage and get the FREE demo.
http://www.erols.com/pvander
------------------------------------------ >>
|