-----Original Message-----
From: John E. Cleeve [mailto:g3jvc@jcleeve.idps.co.uk]
Sent: 09 September 2010 13:02
To: 'W3YY'; 'TowerTalk@contesting.com'
Subject: RE: [TowerTalk] Use of Aluminum Nicropress clamps
Hello Ray,
Over here in EU we use Talurit ferrules, www.talurit.co. it is a
Swedish designed system, and I suggest you read their instructions for
ferrule fixing.
Without you having detailed knowledge of the ferrules used and the
equipment and tooling to fix those aluminium ferrules you describe, to the
guy wires, I would not risk my life and limb climbing that tower, even for a
friend!
It would be a lot safer for you, if your friend hired a cherry
picker/hydraulic platform, and you did the aerial/antenna work from that.
Sincerely, John. G3JVC/GM3JVC.
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of W3YY
Sent: 09 September 2010 11:17
To: TowerTalk@contesting.com
Subject: Re: [TowerTalk] Use of Aluminum Nicropress clamps
Ray -
What really would concern me is that these are not Nicopress sleeves. Who
knows what degree of holding power or quality they will provide. The
Nicopress tools are designed to work with Nicopress sleeves, not just any
random aluminum sleeve one might find in a store.
The fact that the sleeves are aluminum would not seem to be an issue.
Nicopress sells both copper and aluminum sleeves. That said, I've always
used the plated copper sleeves and like them very much. The plating, by the
way, is zinc for regular steel aircraft cable and wire rope and tin for
stainless steel cable. Aluminum sleeves should not be used on stainless
steel cable. Nicopress sells stainless steel sleeves for use with that kind
of cable.
Good luck.
73, Bob - W3YY
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Ray Benny
Sent: Thursday, September 09, 2010 6:56 AM
To: TowerTalk@contesting.com
Subject: [TowerTalk] Use of Aluminum Nicropress clamps
To all,
I am helping a friend install 50 ft of Rohn 25G tower. We are guying it
twice using what I call 'nicropress' clamps around the guy wire insulators
and thimbles. In the past, I have always used the copper nicropress clamps
that are coated with nickel, I think it is.
Well, the fellow went to the local hardware store and a bunch of the
aluminum version of the nicropress clamps. I told him that I have never seen
aluminum nicropress clamps used for guying towers. He then looked in QST and
called a store that sells antenna and tower hardware. They told him that
they were fine for tower guywires.
I'm the one who is going to climb the tower and do the antenna work, but I
just don't feel comfortable climbing a tower with guywires built with
aluminum nicropress clamps.
Am I wrong to feel this way, or have the Aluiminum clamps become the
standard? In other words, are they acceptable replacements for the nickel
plated copper ones?
Another question, are two clamps required per joint? I've seen both one and
two nicropress clamps at guywire joints, but never knew if the second was
required.
Please advise.
Ray,
N6VR
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.851 / Virus Database: 271.1.1/3123 - Release Date: 09/08/10
18:41:00
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|