I think I can answer most of the questions being asked about the FT1000
interface. First of all, Connie, yes you can install the vers. 6.0 Eprom
yourself. I did it in 2002, but didn't write much down, so can't remember
how anymore. But if you order one from Yaesu (Vertek Standard), I'm sure it
would come with some kind of instructions. If not, and you're really
interested, I would be happy to call them (toll free for me, since I live
within 15 miles of them) and get it from a tech. there and relay to you. The
Eprom cost me $9.95 back then +sh/handling.
As to the questions being asked about a resistor, yes there is a fix for
older Eproms. I used that approach before I updated. Per Yaesu, a 2.7k (or
2k7) res. 1/4 watt ok, from Pin 2 (serial out) of the voltage converter
device (be it an FIF232C or homemade device like I used) to radio ground
should make it work, did for me.
For reference, The latest info I have on Vertek Standard is:
Vertek Standard
10900 Walker St.
Cypress CA 90630
Tele 1-714-827-7600
0800 - 1700 PDT (soon to be PST)
Don W6FFH
don.wsixffh@verizon.net
----- Original Message -----
From: "Connie Marshall" <k5cm@azalea.net>
To: <writelog@contesting.com>
Sent: Thursday, October 20, 2005 5:47 PM
Subject: Re: [WriteLog] FT1000 older model and Interface RESISTORS?????
> Can the firmware be updated with out sending the radio to the service
> center
>
> Connie
> K5CM
>
> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com]On Behalf Of Barry
> Sent: Thursday, October 20, 2005 1:19 PM
> To: TRENT SAMPSON; writelog@contesting.com
> Subject: Re: [WriteLog] FT1000 older model and Interface RESISTORS?????
>
>
> Trent,
> I'm not aware of the resistor mod. The pre-V6 firmware caused the
> radio to lock up for 6 seconds while it talked to the computer.
> Apparently, it downloads the complete parameter set when any command
> is sent and takes that long to do it. You need to update the
> firmware.
> Barry W2UP
>
> On 20 Oct 2005 TRENT SAMPSON wrote:
>
>> Greetings All
>>
>> I have heard that the problems with the various interfaces used with
>> aFT1000 can be cured by the use of resistors rather than a firmware
>> change. I am trying to get a FIF232C to work with a FT1000 with 5.92
>> Firmware and it is not playing the game with Writelog
>>
>> Has anyone come across this ?? Thanks in advance
>>
>> Trent vk4ti
>>
>> --
>> No virus found in this outgoing message.
>> Checked by AVG Anti-Virus.
>> Version: 7.0.344 / Virus Database: 267.12.4/143 - Release Date:
>> 10/19/2005
>>
>>
>
> --
> Barry Kutner, W2UP Internet: w2up@mindspring.com
> Newtown, PA Frankford Radio Club
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|