G'day Mike,
Many thanks for your reply. According to the FT990 manual the data bytes
have the following functions:
data1 1/0=TX Clar On/Off, 81h/80h=RX Clar On/Off, ffh=clear offset
data2 0=tune up, 1=tune down
data3 step in khz
data4 step in hz
The program is coded in C++. I believe that there must be a way of tuning
the clarifier using the CAT interface since YAESU has implemented this
function over several models e.g. FT990 and FT1000.
73, Berndt
VK5ABN
> Berndt -
> Probably a typo here, but in your example, shouldn't data 3 be 0x01 to turn
> the (rx) clarifier on ? For what it's worth, I get the same results as you
> do. I'm doing it in Delphi. What are U writing in?
> Sorry I couldn't solve it....But sometimes confirmation the it doesn't work
> is good. Let me know if you get 'er going, and I'll do the same.
>
> 73, Mike NF4L
> opcode | data1 | data2 | data3 | data4 | description
> --------------------------------------------------------------
> 0x09 | 0x00 | 0x00 | 0x00 | 0x64 | Tune up 100 Hz
>
>
> ----- Original Message -----
> From: <wulf@ping.net.au>
> To: <yaesu@contesting.com>
> Sent: Friday, November 29, 2002 9:04 AM
> Subject: [Yaesu] CAT FT990/FT1000 Problem: Clarifier Tuning
>
>
> > G'day,
> >
> > I experience problems setting the clarifier using the CAT interface.
> > The following commands are function ok as expected:
> >
> > opcode | data1 | data2 | data3 | data4 | description
> > --------------------------------------------------------------
> > 0x09 | 0x00 | 0x00 | 0x00 | 0x00 | RX clarifier disabled
> > --------------------------------------------------------------
> > 0x09 | 0x01 | 0x00 | 0x00 | 0x00 | RX clarifier enabled
> > --------------------------------------------------------------
> > 0x09 | 0x80 | 0x00 | 0x00 | 0x00 | TX clarifier disabled
> > --------------------------------------------------------------
> > 0x09 | 0x81 | 0x00 | 0x00 | 0x00 | TX clarifier enabled
> > --------------------------------------------------------------
> > 0x09 | 0xff | 0x00 | 0x00 | 0x00 | Clear Offset
> > --------------------------------------------------------------
> >
> > However I can't seem to set the frequency using the following commands:
> >
> > --------------------------------------------------------------
> > 0x09 | 0x00 | 0x00 | 0x00 | 0x64 | Tune up 100 Hz
> > --------------------------------------------------------------
> > 0x09 | 0x00 | 0xff | 0x00 | 0x64 | Tune down 100 Hz
> > --------------------------------------------------------------
> >
> > Has anyone had success in setting the clarifier through the CAT interface?
> > It almost looks as if the documentation omits some information needed to
> > do so, e.g. which value to set data1 when tuning the clarifier.
> >
> > I'm almost finished with programming a GUI that gives remote control over
> a
> > FT990 (FT1000 without dualband functionallity) and really like to get the
> > clarifier working too.
> >
> > There also seems to be no way in enabling the FAST dial function using
> > the CAT interface, but this can be implemented in software.
> >
> > I welcome any ideas and hints!
> >
> > Many thanks in advance,
> >
> > 73, Berndt
> > VK5ABN
> > _______________________________________________
> > Yaesu mailing list
> > Yaesu@contesting.com
> > http://lists.contesting.com/mailman/listinfo/yaesu
> >
> >
>
>
>
|