Mail Archive Search: <+from:wmoorejr@cox.net>

Results:

References: [ +from:wmoorejr@cox.net: 12 ]

Total 12 documents matching your query.

1. [Amps] 4-400A Plate (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 8 Nov 2002 08:32:19 -0600; I did this same experiment some time back in my Amp Supply LK 500zc. Did it with a 4-250 and 4-400. That amp had 3100 volts idling and I believe a bias zener--don't know the value. Amp keyed with no; /archives//html/Amps/2002-11/msg00123.html (9,073 bytes)
2. [Amps] skin effect (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 4 Oct 2002 13:42:26 -0500; Hi everybody, Assuming the same gauge, is a stranded conductor better than a solid conductor [less skin effect loss because of multiple conductor surfaces] at rf? How about at 60hz? Also can someone; /archives//html/Amps/2002-10/msg00028.html (7,861 bytes)
3. [Amps] skin effect (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 4 Oct 2002 16:05:49 -0500; are some sense. is the tin being lossier than copper, but tin or copper regular stranded [not litz] has no advantage as to skin effect over same gauge solid tin or copper ? Is this right? Once, and o; /archives//html/Amps/2002-10/msg00031.html (9,279 bytes)
4. [Amps] skin effect (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 4 Oct 2002 17:33:24 -0500; strands effect which to wound **Thanks again. This seems to be a hard one to pin down. 3/8" **I would have thought the 7x1mm wires being insulated would have acted like litz wire and been more effici; /archives//html/Amps/2002-10/msg00034.html (10,441 bytes)
5. [Amps] WINDING TANK COILS ......HELP (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 18 Oct 2002 09:15:42 -0500; I think you need to parallel a known value cap with the inductor, then dip and read frequency. Inductance is then found mathematically. If this is wrong I'm sure someone will correct it. 73, Steve; /archives//html/Amps/2002-10/msg00201.html (9,037 bytes)
6. [Amps] WINDING TANK COILS ......HELP (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 18 Oct 2002 09:31:30 -0500; Yep I have them too. I've used them quite a bit. Last time was on some = traps on an antenna. Worked fine--just like my old dipper. Steve -- Original Message --=20 From: K6KWQ@aol.com=20 To: wmoorejr; /archives//html/Amps/2002-10/msg00203.html (7,431 bytes)
7. [Amps] Ameritron parasitic suppressor (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Sun, 1 Sep 2002 17:26:33 -0500; Those suppressors are different from the conventional type that were in my older AL 600H. Mine had an inductor around a resistor [normal looking suppressor] in the lead immediately above each tube. 7; /archives//html/Amps/2002-09/msg00008.html (7,219 bytes)
8. [Amps] filament v (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Sat, 10 Aug 2002 21:43:29 -0500; Hi ampers, While cleaning my Amp Supply LK 500ZC this afternoon I decided to measure filament v. It was 4.64 on 1 tube and 4.68 on the other. Last winter I measured them at 4.79. My voltage runs 245; /archives//html/Amps/2002-08/msg00102.html (6,506 bytes)
9. [Amps] digital pics (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Thu, 22 Aug 2002 15:25:42 -0500; Many of these cameras have excessive time lag, a medicore "atom bomb" flash, [no nice off the film metered flash as was common with 35mm], poor pics indoors, barely acceptable lenses, too much time b; /archives//html/Amps/2002-08/msg00205.html (9,030 bytes)
10. [Amps] rocky point effect, barnacle bill (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Fri, 23 Aug 2002 16:58:53 -0500; For what it is worth dept. A while back I bought a used Ameritron AL 800H that uses a pair 3cx800. About a minute or so after I first turned it on [nothing hooked to it but the power cord] I heard a; /archives//html/Amps/2002-08/msg00240.html (8,233 bytes)
11. [Amps] bangs in 3cx800 (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Sat, 24 Aug 2002 14:11:55 -0500; I'm here to learn too. I found the manual to be very thorough. Maybe they are just being honest. I see no obvious reason why the AL 800H design has anything to do with an Eimac 3cx800 banging. Maybe; /archives//html/Amps/2002-08/msg00249.html (9,097 bytes)
12. [Amps] bangs in 3cx800 (score: 1): Author: wmoorejr@cox.net (Steve M); Date: Sat, 24 Aug 2002 15:14:29 -0500; Oops.... The diode is on the ps board. Steve; /archives//html/Amps/2002-08/msg00251.html (7,192 bytes)

Current List: 1 - 12
Page: [1]