Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+High\s+temp\s+magnet\s+wire\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+High\s+temp\s+magnet\s+wire\?\s*$/: 17 ]

Total 17 documents matching your query.

1. [Amps] High temp magnet wire? (score: 1): Author: "Tim Duffy" <k3lr@k3lr.com>; Date: Sun, 2 Dec 2018 11:20:35 -0500; Looking for #20 high temperature magnet wire - sometimes referred to as Thermaleze. Any ideas? Need high temp rating for a plate choke rebuild. 73 Tim K3LR ___________________________________________; /archives//html/Amps/2018-12/msg00002.html (6,426 bytes)
2. Re: [Amps] High temp magnet wire? (score: 1): Author: RCM <robrk@nidhog.net>; Date: Sun, 2 Dec 2018 21:31:23 -0500; https://www.amidoncorp.com/thermaleze-coated-magnet-wire/ <https://www.amidoncorp.com/thermaleze-coated-magnet-wire/> https://ca-en.alliedelec.com/wire/magnet-wire/ <https://ca-en.alliedelec.com/wir; /archives//html/Amps/2018-12/msg00003.html (7,956 bytes)
3. Re: [Amps] High temp magnet wire? (score: 1): Author: Stan Gammons <s_gammons@charter.net>; Date: Sun, 2 Dec 2018 20:08:55 -0600; http://www.amidoncorp.com/thermaleze-coated-magnet-wire/ 73 Stan KM4HQE Any ideas? Need high temp rating for a plate choke rebuild. 73 Tim K3LR _______________________________________________ Amps ma; /archives//html/Amps/2018-12/msg00004.html (7,353 bytes)
4. [Amps] High temp magnet wire? (score: 1): Author: "Jim Thomson" <jim.thom@telus.net>; Date: Mon, 3 Dec 2018 07:37:12 -0800; <Looking for #20 high temperature magnet wire - sometimes referred to as <Thermaleze. <Any ideas? <Need high temp rating for a plate choke rebuild. <Tim K3LR lab supply, and ran 5 Amps CCS through it; /archives//html/Amps/2018-12/msg00006.html (7,911 bytes)
5. Re: [Amps] High temp magnet wire? (score: 1): Author: Jim Klein <k7rdx@charter.net>; Date: Mon, 3 Dec 2018 09:12:35 -0800; I use 20g for my YC-156 choke works fantastic..Jim..K7RDX.... _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps; /archives//html/Amps/2018-12/msg00007.html (9,574 bytes)
6. Re: [Amps] High temp magnet wire? (score: 1): Author: "Peter Voelpel" <dj7ww@t-online.de>; Date: Mon, 3 Dec 2018 18:20:22 +0100; Will become extremely hot when positioned next to a pair of 4-1000A or similar. 73 Peter, DJ7WW <Looking for #20 high temperature magnet wire - sometimes referred to as <Thermaleze. <Any ideas? <Need; /archives//html/Amps/2018-12/msg00008.html (8,085 bytes)
7. Re: [Amps] High temp magnet wire? (score: 1): Author: "Jeff DePolo" <jd0@broadsci.com>; Date: Mon, 3 Dec 2018 12:20:08 -0500; High-temp as in 200 deg C? That's what most polyamide magnet wires like Thermaleze are rated for. Enamel-coated is rated lower, like anywhere from 120C to 200C depending on the type. I've bought mag; /archives//html/Amps/2018-12/msg00009.html (8,573 bytes)
8. Re: [Amps] High temp magnet wire? (score: 1): Author: Bill Turner <dezrat@outlook.com>; Date: Tue, 4 Dec 2018 01:12:22 +0000; If I remember right, Thermaleze is not considered high temp wire. It is made so that it can be stripped with just the heat of a soldering iron. Real hi temp wire has enamel that will not melt at sold; /archives//html/Amps/2018-12/msg00012.html (7,832 bytes)
9. Re: [Amps] High temp magnet wire? (score: 1): Author: Jim Garland <4cx250b@miamioh.edu>; Date: Tue, 4 Dec 2018 10:09:29 -0700; I believe Bill is correct. However, since K3LR's intended use is to repair a bad monoband 40m plate choke, the temperature specifications of the wire are not important. I'm sure Bill would agree with; /archives//html/Amps/2018-12/msg00023.html (9,251 bytes)
10. Re: [Amps] High temp magnet wire? (score: 1): Author: Manfred Mornhinweg <manfred@ludens.cl>; Date: Tue, 04 Dec 2018 20:52:14 +0000; Jim, lab supply, and ran 5 Amps CCS through it for 1 hr, stone cold. 22 gauge was used on a buddys 3x6 amp, all bands. AWG#22 is good for roughly one ampere in tight windings inside large transformer; /archives//html/Amps/2018-12/msg00024.html (12,788 bytes)
11. [Amps] High temp magnet wire? (score: 1): Author: "Jim Thomson" <jim.thom@telus.net>; Date: Wed, 5 Dec 2018 11:06:26 -0800; Jim, AWG#22 is good for roughly one ampere in tight windings inside large transformers, and at least 3A in bundles. 5A is a bit high, but in free air it's OK. If you wind that wire close-spaced into; /archives//html/Amps/2018-12/msg00033.html (16,076 bytes)
12. Re: [Amps] High temp magnet wire? (score: 1): Author: Manfred Mornhinweg <manfred@ludens.cl>; Date: Fri, 07 Dec 2018 19:21:02 +0000; Jim, through the choke. Even W8JI doesnt buy into it either. Its more like RF RMS vac / Choke Z. I fully agree with that! It's just that I was assuming that at least on the lowest bands, which are mo; /archives//html/Amps/2018-12/msg00041.html (20,288 bytes)
13. [Amps] High temp magnet wire? (score: 1): Author: "Jim Thomson" <jim.thom@telus.net>; Date: Mon, 10 Dec 2018 01:23:30 -0800; <<<Would like to see that. Is it piblished somewhere? <Manfred Scroll to the bottom to see his VNA results. For choke dissipation he is using RMS voltage squared / RP. RMS RF voltage = 60% of loaded; /archives//html/Amps/2018-12/msg00071.html (10,337 bytes)
14. Re: [Amps] High temp magnet wire? (score: 1): Author: "Peter Voelpel" <dj7ww@t-online.de>; Date: Mon, 10 Dec 2018 17:11:57 +0100; I tried that choke in my 3x 4-400 amplifier, it immediately went up in smoke on 17m. 73 Peter, DJ7WW <<<Would like to see that. Is it piblished somewhere? <Manfred Scroll to the bottom to see his VNA; /archives//html/Amps/2018-12/msg00074.html (9,064 bytes)
15. Re: [Amps] High temp magnet wire? (score: 1): Author: AJ <iamfromcanadaalso@gmail.com>; Date: Mon, 10 Dec 2018 14:34:56 -0500; Hi People All I have ever done is go to my local motor rewinding shop. Last time there I purchased 400 feet of 21 ga, iirc I paid $50.00 about 6 months back. They have it by the mile; are quite reaso; /archives//html/Amps/2018-12/msg00076.html (9,170 bytes)
16. Re: [Amps] High temp magnet wire? (score: 1): Author: Manfred Mornhinweg <manfred@ludens.cl>; Date: Tue, 11 Dec 2018 16:03:05 +0000; AJ, All I have ever done is go to my local motor rewinding shop. Last time there I purchased 400 feet of 21 ga, iirc I paid $50.00 about 6 months back. You overpaid by a factor of at least 10! They h; /archives//html/Amps/2018-12/msg00079.html (9,407 bytes)
17. Re: [Amps] High temp magnet wire? (score: 1): Author: Jim Klein <k7rdx@charter.net>; Date: Wed, 12 Dec 2018 15:53:59 -0800; Try Ebay,I have many spools bought there for very reasonable prices,,,Jim,K7RDX.. _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mai; /archives//html/Amps/2018-12/msg00083.html (9,931 bytes)

Current List: 1 - 17
Page: [1]