Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+LK550\s+ALO\/Meter\s+board\s+interconnect\s+\-\s+anyone\s+know\s+what\s+the\s+manufacturer\s+or\s+part\/type\s+of\s+the\s+two\s+6\-pin\s+nylon\s+connectors\s+tha/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+LK550\s+ALO\/Meter\s+board\s+interconnect\s+\-\s+anyone\s+know\s+what\s+the\s+manufacturer\s+or\s+part\/type\s+of\s+the\s+two\s+6\-pin\s+nylon\s+connectors\s+tha/: 6 ]

Total 6 documents matching your query.

1. [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: wb0gaz via Amps <amps@contesting.com>; Date: Wed, 1 Nov 2023 21:29:46 +0000 (UTC); Thanks (Dave) for insight on the panel meters. Arriving to the point (on LK550) that the ALO/Meter board is suspect - either was damaged or caused damage in it's prior life. Several traces handling 1; /archives//html/Amps/2023-11/msg00000.html (8,043 bytes)
2. Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: gudguyham--- via Amps <amps@contesting.com>; Date: Wed, 1 Nov 2023 22:26:35 +0000 (UTC); Dave, the ALO boards on these amps are for the most part worthless. They dont trip on the important factors anyway. When they go bad I usually just bypass them. Not worth the effort to repair them; /archives//html/Amps/2023-11/msg00001.html (12,093 bytes)
3. Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: wb0gaz via Amps <amps@contesting.com>; Date: Wed, 1 Nov 2023 22:33:22 +0000 (UTC); Thanks! That is consistent with my thought - with 3-500Z tubes, there's nothing to be gained as long as the op pays attention... If I can identify the PCB-end connectors in use, that will reduce the; /archives//html/Amps/2023-11/msg00002.html (12,510 bytes)
4. Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: gudguyham--- via Amps <amps@contesting.com>; Date: Wed, 1 Nov 2023 22:50:32 +0000 (UTC); The board trip simply cuts out the 12v to the antenna relay board. I just cut the 12v line and connect it to the line out to the relay. End of story. Sent from the all new AOL app for iOS Thanks!; /archives//html/Amps/2023-11/msg00003.html (12,985 bytes)
5. Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: wb0gaz via Amps <amps@contesting.com>; Date: Wed, 1 Nov 2023 22:55:09 +0000 (UTC); So remove 12V going into the ALO/Meter board (that came from the xmt/stby switch), leave the two meters and associated resistors in place (they're passive), and send the now-removed 12V that went to; /archives//html/Amps/2023-11/msg00004.html (12,610 bytes)
6. Re: [Amps] LK550 ALO/Meter board interconnect - anyone know what the manufacturer or part/type of the two 6-pin nylon connectors that mate with J1/J2 on the ALO/Meter board? (score: 1): Author: gudguyham--- via Amps <amps@contesting.com>; Date: Thu, 2 Nov 2023 03:22:23 +0000 (UTC); Basically yes. 12volts comes up from the 12v supply and feeds the ALO board. If all is good it sends -2v to the relay. The ALO board interrupts that in a fault so just bypass it to the relay. S; /archives//html/Amps/2023-11/msg00005.html (13,415 bytes)

Current List: 1 - 6
Page: [1]