Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Removing\s+enamel\s+insulation\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Removing\s+enamel\s+insulation\?\s*$/: 11 ]

Total 11 documents matching your query.

1. [Amps] Removing enamel insulation? (score: 1): Author: "Joe Subich" <joe@subich.com>; Date: Sun, 20 Feb 2005 13:14:16 -0500; Does anyone have a good way to remove enamel (Formvar?) from thin wires? Scraping/sanding works fine for large wires but doesn't work too well for thin wires. Is there a chemical that will do the job; /archives//html/Amps/2005-02/msg00622.html (7,275 bytes)
2. Re: [Amps] Removing enamel insulation? (score: 1): Author: Vic Rosenthal <vic@rakefet.com>; Date: Sun, 20 Feb 2005 10:21:02 -0800; The usual way it's done with 'modern' enameled wire (possibly not Formvar) is by dipping it in molten solder. A solder pot or the nose of a Hakko 808 desoldering tool works well. Lacking these, a blo; /archives//html/Amps/2005-02/msg00623.html (7,390 bytes)
3. [Amps] Removing enamel insulation? (score: 1): Author: "Will Matney" <craxd1@ezwv.com>; Date: Sun, 20 Feb 2005 13:36:32 -0500 (Eastern Standard Time); Joe, There's a small handheld tool made just for this. It looks like the jaws of a large toe-nail clipper with a handle that has a small curve in the bottom to fit the palm back of your hand. You sim; /archives//html/Amps/2005-02/msg00626.html (8,532 bytes)
4. [Amps] Removing enamel insulation? (score: 1): Author: "Will Matney" <craxd1@ezwv.com>; Date: Sun, 20 Feb 2005 13:47:37 -0500 (Eastern Standard Time); is by transfer Vic, that's only good for sodereze wire. Sodereze has a low insulation melting point made for low voltage work and or low heat work. You can get that kind of wire from Radio Shack and; /archives//html/Amps/2005-02/msg00628.html (7,946 bytes)
5. Re: [Amps] Removing enamel insulation? (score: 1): Author: DaleLeStourgeon <dlestourgeon@cox.net>; Date: Sun, 20 Feb 2005 12:51:56 -0600; There was an article a while back in Electric Radio that recommended using an asprin, solder, and soldering iron all together. Supposedly takes off the enamel and tins at the same time. 73 Dale K5AJZ; /archives//html/Amps/2005-02/msg00630.html (8,166 bytes)
6. Re: [Amps] Removing enamel insulation? (score: 1): Author: "Steve Thompson" <g8gsq@ic24.net>; Date: Sun, 20 Feb 2005 19:07:09 -0000; I'm trying to remember my early days with crystal sets, using recovered wire from transformers - I think it was before self fluxing wire became the norm. I used to use a flame, then clean up with wir; /archives//html/Amps/2005-02/msg00631.html (7,851 bytes)
7. Re: [Amps] Removing enamel insulation? (score: 1): Author: "Bob Maser" <bmaser@tampabay.rr.com>; Date: Sun, 20 Feb 2005 18:28:31 -0500; On the flip side of the coin, I have some Formvar coated wire that is at least 15-20 years old and I find that if I try to wind it into a diameter smaller than 1" it cracks the formvar coating. Is th; /archives//html/Amps/2005-02/msg00633.html (9,777 bytes)
8. Re: [Amps] Removing enamel insulation? (score: 1): Author: "Mike Sawyer" <w3slk@uplink.net>; Date: Sun, 20 Feb 2005 18:59:21 -0500; Back when I worked for EIT, I had to build detonators by hand. Essentially they were nothing more than a dc-dc amp with a boost. Anyhow, I used to use a chemical substance that was fairly high pH. I; /archives//html/Amps/2005-02/msg00634.html (8,540 bytes)
9. Re: [Amps] Removing enamel insulation? (score: 1): Author: R.Measures <r@somis.org>; Date: Sun, 20 Feb 2005 16:08:39 -0800; Formvar is history. Recycle it and buy some modern, silicone-varnished 200ºC Cu wire from an electric motor rewinding shop. Bring your own empty spool and winder - unless you need a 35-pound rol; /archives//html/Amps/2005-02/msg00637.html (11,110 bytes)
10. Re: [Amps] Removing enamel insulation? (score: 1): Author: R.Measures <r@somis.org>; Date: Sun, 20 Feb 2005 16:11:59 -0800; This is how I do it. A flame combusts the varnish but it does not damage the Cu. Richard L. Measures, AG6K, 805.386.3734. www.somis.org _______________________________________________ Amps mailing li; /archives//html/Amps/2005-02/msg00638.html (9,563 bytes)
11. Re: [Amps] Removing enamel insulation? (score: 1): Author: ToddRoberts2001@aol.com; Date: Sun, 20 Feb 2005 19:55:05 EST; Is there a chemical that will do the job (dip/wipe)? I have used paint remover to do this. The gel kind works well. Put some paint remover into a metal bottle cap or some similar small container and; /archives//html/Amps/2005-02/msg00640.html (8,331 bytes)

Current List: 1 - 11
Page: [1]