Hi Rick, I can't address your network issues but I can tell you that I have successfully used the DVP will CT versions 9.63, 9.64 and 9.65. I have not tried any more recent versions with the DVP. 73
Hi guys, I want to use to 2 Win98 laptops networked to run CT in DOS mode. I wanted to know if it is possible to network CT through the USB ports? Would this be done through a hub? If not, Is it poss
HI Guys, Why not just e-mail N8BJQ again to clarify how the actual logs will be handled? He oversees the contest and enforces the rules so it seems to me that whatever he says is what actually should
Hi guys, My computers are doing weird things with CT9.53 and CT9.65 so I would appreciate any insight and/or help into possible solutions. Both computers are 486 vintage with adequate RAM and hard-dr
HI Dave, YES! The ctrl-f6 key was the culprit. Re-recording it caused the F2 key to work properly again. While that should make the Serial number issue go away, you would think that in a contest w/o
Bill, I have had similar problems before with one-way transmission. It was usually because the RS232 chip (CAT Port) was blown in the 'MP - the MAX232CWE surface mounted chip on the control board was
Hi Bill, Yes, I read the message and the subject. One time I had a problem that allowed one-way communication from the computer to the radio but not from the radio to the computer AND it worked with
Ken, Since you are working on a new version prior to WAE, what about my request to go back and resend and relog QTC? (that has previously been sent and logged). Presently if we have sent QTC, it is g
Hi Dennis, To add further information, both stack matches had numerous blown diodes and one There is no doubt - you had at least one nearby lightning strike. Either a direct strike or something came
Hi Guys, Weird problem just developed with BOTH FT1000MP's. I am using 2 FT1000MP's on 2 computers with CT ver 9.53. When I used this setup in WPXCW, CT, BOTH radios and both computers talked to each
Thanks for all the responses! Here are a few more details and what I have tried: Running only Dos 6.22 with both computers Radios are in normal mode not mem mode Master CPU reset - did not fix Swappe
Correct - I switched com ports and the computers talked to each other. I switched com ports back and the computers talked to each other. Only the radios and computers won't talk to each other, regard
HI George, Thanks for the suggestion - I am well aware of loading and unloading the CTTSR's etc. I am using CT version 9.53 - same as before - so that's not it. Thanks for trying to help! 73 Bob KQ2M
Yes - everything disconnected. I just ran out to Radio Shack and bought the RS232 tester - I remember that you knew how to interpret the signals so here they are: Radio alone (either Com port same re
Hi Gary, Good suggestion but no Windows on either computer. There is no modem on either computer. Thanks for your thoughts - I'm sure this will come in handy someday. 73 Bob KQ2M Learned -- WWW: http
Hi Ken, CT 9.64 does work with the Digiboard and the Expanded mult lists were nice to have. I experienced some weird stuff though and thought maybe you could shed some light on it, as well as have so
Author: Robert Shohet" <kq2m@mags.net (Robert Shohet)
Date: Mon, 4 Dec 2000 09:30:12 -0500
I have a very vexing problem with my DVP. I programmed the record functions this morning with F3 as "59 Connecticut" and of course F5 gives the guys call which for purposes of this test was "G3FXB".
Author: Robert Shohet" <kq2m@mags.net (Robert Shohet)
Date: Mon, 4 Dec 2000 11:43:11 -0500
Tnx Joe and Ed for your replies. Here are the relevant commands that I am using: In the config.sys file on the C:\ root directory: DEVICE=C:\DOS\RAMDRIVE.SYS 1024 512 128/E In the Autoexec.bat file o
Author: Robert Shohet" <kq2m@mags.net (Robert Shohet)
Date: Mon, 4 Dec 2000 13:18:45 -0500
Ed & Pete, Tnx for your suggestions... There is no keyboard.ini file on any of my DOS based computers. Any suggestions on where to find this? The PATH statement is as follows: PATH=C:\DOS,C:\,C:\CT9,
Author: Robert Shohet" <kq2m@mags.net (Robert Shohet)
Date: Mon, 4 Dec 2000 13:52:47 -0500
Hi Don, The F3 was a typo and was corrected in the next reflector posting. F3 contains a QRZ? not a 3A 3A 3. F2 is 59 Connecticut. DVP is reading this differently though. Any other suggestions? Tnx &