is bridging disabled? check ARP tables also...it's recommended that you login to the unit via its outside interface IP -Charles --Original Message-- From: karlnet-admin@WISPNotes.com [mailto:karlnet-
yes Actually, bridging is enabled, and I take it that is the problem. Brett interface and directly radio _______________________________________________ Karlnet mailing list Karlnet@WISPNotes.com htt
yup Thanks to Charles for the answer to my configurator issue. I turned off bridging on all my clients and selected inhibit NAT from 802.11b interface as well. I am wondering if having bridging enabl
shipping in a few weeks...offlist if you want to pre-order... btw...anyone in San Jose for WCA, give me a shout - 773-457-0718 (cell) -Charles --Original Message-- From: karlnet-admin@WISPNotes.com [
we're still trying to figure out how to use the new site... -Charles --Original Message-- From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On Behalf Of Dan Metcalf Sent: Saturday
pricing for the 1 port board - $150 w/out power supply or card pricing for the 2 port board - $185 w/out power supply or card offlist if you want to be put on the beta list specs below... Full Versio
next week <g> they've encountered a few bugs along the way...and things have slowed down a bit - if you want, we can put you on the beta list, so that you can be assured to receive the boards the min
yes...it will have support for Prism cards - no more worries about overdrawing the RGs (in terms of power) in terms of 5.x support, yes cardbus is supported...however, someone needs to manufacture a
both - read the specs below When you say 2 port board....is that 2 Ethernet or 2 PCMCIA ports? weren't _______________________________________________ Karlnet mailing list Karlnet@WISPNotes.com http:
not the same measurements (but generally pretty close), but the wholes are in the same spot...one card on top, one card on bottom So the dual slot board is the same measurements of the rg1000? Dan Me
no -- you need SE-4500 however, some KarlNet vendors will let you swap out SECs for SRs when the time is right to upgrade your network -Charles --Original Message-- From: karlnet-bounces@WISPNotes.co
they still sell it -Charles Does anybody know for sure that Karlnet is still offering the linux driver? I'm thinking of doing some work with it but don't want to mess with it if they are dropping or
yes Hi Kevin, Does the satellite software support a KN client on one radio, and a 802.11b AP in the other? Norm on application. driver? _______________________________________________ Karlnet mailing
upgrade firmware Seems like I read here that there are some issues with the ethernet port of an AP-1000 running KN. I have an AP-1000 that has at least 7% packet loss communicating on the ethernet in
can't Route & run NAT at the same time -Charles Can someone please tell me how to configure a KN AP on an AP-1000 to do routing and allow users to connect? I'm having a devil of a time. I have the fo
works fine -Charles --Original Message-- From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On Behalf Of George Minich Sent: Wednesday, December 11, 2002 8:49 AM To: karlnet@WISPNo
what type of COR? does it have a BNC connector or an RS-232? Your processor may be getting overloaded -Charles --Original Message-- From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.c
larry (who runs 11b) might be talking about 802.11b w/ similar pass phrases - it can be a huge problem, especially in SEC bridges on AP-Plus - not really an issue in TurboCell --Original Message-- Fr
so you're a reseller for Aperto? congrats... www.apertonet.com - to bad their web page sucks -Charles John In about 3-4 weeks we will be offering a 20Mb system (14Mb usable) 5.8Ghz that will do 13 mi
if you're willing to pay $50kish for the base -Charles How about the rest of these Aperto products...... Are they any good? PacketWave 110 for residential subscribers Bridging; support for up to 5 ho