Do you guys have storm protection turned on? I had this same problem w/ v4.31. Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bo
check under AP station entries, sometimes you'll see them in there. Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bounces@WISPN
On cpe's I use the defaults, on the AP'S I use much higher numbers. When we first upgraded our AP's to v4.31 code, we had the default storm protection set and had enabled the "IP ARP CACHE" and that
How is the "speaker" on it, does it work for link tests? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bounces@WISPNotes.com] c
The senao cards I have used seem to over heat and RX became a problem.... are you able read the signal's? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsy
Caleb, I am just wondering if you have personally confirmed that the updated firmware allows the link test to work? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.me
Kevin, How soon can we expect the "auto-roam" and vlan updates? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bounces@WISPNotes
Bob, ISP base allows NDIS clients (windows clients). Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bounces@WISPNotes.com] and b
That will happen if that link is hitting that bw limit Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com [mailto:karlnet-bounces@WISPNotes.com] and
I don't use the bw limits on the ap, only on the cpe's and then we use a linux box running cbq to throttle internet traffic Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-278
When using the sr4100 as a PtP controller, you can't select "non-polling" w/ version v4.xx code, it just blanks that option Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-278
I switched our network from bridged ( 4 AP'S, all bridged :-)) to a fully routed network running RIPv2... now I have networks all over the place :-) performance though is very good and broadcasts are
Does karlnet have a driver for PDA's? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com -- [This E-mail scanned for viruses by Declude Virus]
Any updates on the outdoor units? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com -- [This E-mail scanned for viruses by Declude Virus]
NO doubt, KARLNET - WE NEED SOMETHING TO graph snr over time, I use mrtg & cricket, but I have yet to actually do that or see a working script! Dan Metcalf Wireless Broadband Systems http://www.wbsys
I have a link like this 1 2 3 4 Rg1000--ap1000--ap1000--rg1000 Both ap's are running isp base station, but when going across from rg to rg I see latency at 200ms Any thoughts? Dan Metcalf Wireless Br
2 ap's, 2 radio's in both ap's... the 1st ap is set for isp base(radio a)/satellite (radio b) from the ethernet on the 2nd AP pinging across the 1st AP I see the latency Dan Metcalf Wireless Broadban
Actually its like this Link)--AP1000--!wirelesslink!--AP1000--(Wireless even if we take out the last "rg" and connect from the Ethernet port of the 2nd AP1000, when pinging radio "b" on the 1st ap, I
Net id and channel # are different. One is ch 6 and the other is ch 11, but both are v-pol Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2780 dan.metcalf@wbsysnet.com On one