Does this increase performance at all? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com -- [This E-mail scanned for viruses by Declude Virus]
<o:p> </o:p> I have an ap1000 which is on radio B. and we are seeing a very HIGH # of FCS errors (In errors). There is only 1 CPE on this radio, should I see the same # errors on the Outside of the C
Lets say it's a weak or low signal from the client, would anything on the client indicate this? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com On the
NO amps in the system. I just wanted to double check. I think it's a mis-aligned antenna at the site, I told the installer to turn it 6*, he turned it like 20* Dan Metcalf Wireless Broadband Sytems d
I'm looking over the firewall setup on the karlnet v4.02, and I'm wondering how I can block SPECIFIC ports (135-139, 5000) and allow everything else, as it looks like by default you configure what yo
Since we upgraded most of our units to v4.02, we have noticed problems w/ the bandwidth settings. is this a known bug to karlnet? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wi
Sometimes it takes the lower speed and locks all the interfaces down to that speed Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com On -- [This E-mail s
How can we verify if they are prism 2 or prism 2.5? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com On the results cannot fix it They [mailto:karlnet-a
Doug, I thought you stated that the prism 2.5 cards do work (100mw and 200mw) Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com On isn't [mailto:karlnet-
Same problem here Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com On w/TC... and from was, correctly whether or [mailto:karlnet-admin@WISPNotes.com] in
I seen a high amount of Out Errors/Out carrier sense errors on the Ethernet part of the AP, but I can't find a reference to these any were??? Thanks, Dan Metcalf Wireless Broadband Sytems dan.metcalf
Tony, Can we clarify what DOUG said? I thought he said the prism 2.0 cards DO NOT work and the PRISM 2.5 cards do work (100 & 200mw)? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com ww
NATE, I have the SNR 1 often w/ any non-lucent cards in the ap's, & rg's. are you using an ap or an rg? Dan Metcalf Wireless Broadband Sytems dan.metcalf@wbsysnet.com www.wirelessbroadbandsystems.com
Norm I don't think its TONY's issue. Actually I have had ok LUCK w/ the PRISM 2.5 cards in the rg1000's. I haven't yet tried them in the AP? (anybody have any prism 2.5 cards working ok in the ap1000
I'd like to upgrade several units as well :-) -- [This E-mail scanned for viruses by Declude Virus] _______________________________________________ Karlnet mailing list Karlnet@WISPNotes.com http://
Whats the current status of the 5.x support? I saw a mention of radiolan cards? But are these available? -- [This E-mail scanned for viruses by Declude Virus] ________________________________________
I agree, karlnet needs to speed things up a lot... [mailto:karlnet-bounces@WISPNotes.com] board PoE, but -- [This E-mail scanned for viruses by Declude Virus] ________________________________________
No reply from karlnet??? [mailto:karlnet-bounces@WISPNotes.com] want to about on Atheros deploy now, near do it - with are access backhaul manages forever. Atheros be late it, -- [This E-mail scanned
Reg, What about the update for the KN50, when will that be available? Some of my kn50's have a 50% retrans rate Thanks, Dan [mailto:karlnet-bounces@WISPNotes.com] 14.75Mbps.The TurboCell rates the re