How about we put together a list of possible radio/antenna combos that we want to use and split the costs for fcc certs? Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 w
Did you have to configure the interface's on the cpe's or just put the card in and reboot? Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.co
I agree with that, you should include the ANDREWS 24db Antenna as well Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com I'd be interested
Peter, I have done various tests with the rg1000's in point to point and point to multipoint, you have a total amount of bandwidth available of about 5.5Mb/s. Since the radio is half-duplex you can't
Actually I should have said you can get 5.5Mb's in both directions at the same time Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Peter
Well it's a long day, you can't get 5.5mbps in both direction at the same tiem Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Actually I
Interesting results, Was it just that card or all of the supposed 200mw cards? Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Gentlemen
Scott, Are you saying you see 17db with these cards as well? Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Not as per Karlnet. Proposit
I see a high number of In Errors/FCS Errors on my AP, should I be able to match these errors w/ outbound errors at my CPE? Or could random *noise* cause these as well? Dan Metcalf Wireless Broadband
I have a setup with with 2 rg1000's w/ the soho bin, 1 had a link to the ap already, when the 2nd went online it had the other rg1000 listed in its turbocell stations list from the manager, is this n
Bill, Do you have a subnet calculator? That will do all the work for you Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Yes. I understan
Make sure you have a subnet calculator Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com Sounds like interesting stuff, but how to get star
Does this impact performance? Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com I think I've seen this too, Dan. As long as the two can "se
I have an rg1000 w/ v4.02 and a 200mw card, tested it out and it seemed ok, installed it at a customers location and something isn’t good.<o:p></o:p> <![if !supportEmptyParas]> <![endif]><o:p><
Norm<o:p></o:p> <![if !supportEmptyParas]> <![endif]><o:p></o:p> Actually the prism II card is in the cpe (rg1000), I’m thinking it might be a bad cable to the antenna, not sure as I can do a w
I use common words for SNMP such as samadams, beer, goodbeer, ... etc Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com This program is a m
As a cisco engineer, I found the routing setup on the lucent ap's different at first, but then after playing with it I realized you make "interface's" with each direct route. I would use either routi
You can set both so that you can bridge IPX and ROUTE IP Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 www.wirelessbroadbandsystems.com So that is why you can set the t
$275 for POE and outdoor box is a good deal (and karlnet license)<o:p></o:p> <![if !supportEmptyParas]> <![endif]><o:p></o:p> Dan Metcalf<o:p></o:p> Wireless Broadband Systems<o:p></o:p> dan.metcalf@
I though the ap1000 had a 133mhz and the wavepoint II has a 66mhz?? Since Karlnet uses polling this will have an impact Dan Metcalf Wireless Broadband Systems dan.metcalf@wbsysnet.com 781-658-2075 ww