Hi, Seems as though no matter what we input into the configuration pages for these KN-50 board, when we save and restart the unit, it sets everything back to defaults. Are we doing something wrong he
Are these things JUNK, or what??? We set to auto channel scan, then our AP sees the KN-50 for a few seconds, then it drops out, and over and over again. So we set it to channel 1 only, our AP shows i
The board is mounted in one of your 19dB antennas, so I don't think the button is being pressed... I don't seem to see a section for network ID, can you point this out? Regards, Jayson A. Baker Peak
Not as such yet. Regards, Jayson A. Baker Peak Internet Solutions Did you actually get one to work with the stock card? Andy Henckel MultiBand Communications A TransAria Company 415 N. Higgins Ave. S
Hi, Now that we're going to be using the KN-50's (if we get them tow work!) and most of our customers will elect to just use a switch instead of router for multiple machines. Does anyone have problem
Yes... Reg is the man. I'll be talking to him in the AM! :-) Regards, Jayson A. Baker Peak Internet Solutions Jayson, I am sure you just need to work through some settings issues. I was as reluctant
We provide a public IP and up until today (when we got a KN-50) have always gone directly into one machine or into a router. What's the difference if the customer has one machine or 5 on the connecti
We cooked one of the KN-105's at 165F for 60 minutes here in the office not too long ago... It continued working just fine, passing the same amount of data as when it was cool (I don't remember exact
About 5 feet. Regards, Jayson A. Baker Peak Internet Solutions Jayson -- You used a 24VDC POE? How long of an ethernet cable? Dan Metcalf Wireless Broadband Systems http://www.wbsysnet.com/ 781-577-2
Do the 200mW Senao cards no longer work in the KN-100 boards? All I get is a blinking light, and the board stops booting (cannot access config, etc.). Running SG4001 software. Regards, Jayson A. Bake
Supposedly they work in TC mode, just not 802.11 mode. Why? Same thing on an older WavePoint II w/ Karlnet firmware. Regards, Jayson A. Baker Peak Internet Solutions Do the 200mW Senao cards no longe
We're in the process of implementing Motorola Canopy throughout our entire coverage area because they listen to our requests and make software that fits our needs (i.e. all CPE's just got the feature
As do we. We just implemented NAT/DHCP on everything across the board. Regards, Jayson A. Baker Peak Internet Solutions We almost exclusively use Karlnet SEC with NAT AND DHCP. I'd say about 5 out of
Yup. But they brought them back until end of November so you can "stock up" Regards, Jayson A. Baker Peak Internet Solutions --Original Message-- From: karlnet-bounces@WISPNotes.com [mailto:karlnet-b
Especially when Motorola just released a 2.4GHz product - by far, will blow anything 802.11 away, especially the high prices of Karlnet. Regards, Jayson A. Baker Peak Internet Solutions Exactly, Karl
Not seen this integrated unit... specs on it? Must also add software license? Power supply? What about us who shoot 20+ miles and need 24dBi dishes? Regards, Jayson A. Baker Peak Internet Solutions t
I don't know. Ask Motorola. I only heard it was released. Regards, Jayson A. Baker Peak Internet Solutions Jayson, What are the specs on the 2.4ghz stuff? Thanks, Dan [mailto:karlnet-bounces@WISPNote
YDI does, they call it "YDI-Fi" (Karlnet) Regards, Jayson A. Baker Peak Internet Solutions We have been using the Etherant for the last 2 years. I wanted something better with throttling. I live in M
Routing is routing is routing. Whether you're using private IP's and routing public over it, or just routing public - you're still routing. If you're only doing a point-to-point-to-point link I'd rec
So the one in the middle, the KN-200, is in routing mode, with no IP's? Go to either RG on either end, set them to bridging mode - plug in your laptop to the Ethernet port and hit scan, you'll see th