Hello I had a similar problem with the Paragon. The problem was solved with the new firmware form tentec. Before I had a chirpy signal when running QSK and split 73 de Harry, DK2GZ
Hello yes the new firmware will cure the problem. I got the new firmware about one year ago. Super TenTec service even for older brands! The Giehl chip will cure the problem also, but the timing for
Hello it is more easy, then discon the jumper on the back of the OMNI 6+ Hit the "ST" button, you will hear the sidetone, then hit the "CW" button and you are off the air. Hit the "ST" button again a
Hello I have a similiar problem with an OMNI 6+, but only on 80 meter with the tx. Sometines the tx maybe not transmitting on the 80 meter band, because the swr is droppend very high, the sidetone ge
Hello from time to time the TX maybe jumped off the band, and I noticed a very big jump in the SWR and the power dropped down for a few milliseconds, then the TX comes back. The problem is also with
Hello did you ever look or listen on a second RX at your cw-shape forms in qsk, when using a 756 proII? The RX maybe good, but the qso-partners maybe have problems to copy your choppy cw-sound in qsk
Hello I am using the LP all the time on my OMN6+. It reduce the high hiss in the rx-chain very nicely. In the original 6+ you can set the frequency, by still hold the button pressed. There is also a
Hello from Germany, I am using also an OMNI 6+. My 6+ is about +200 HZ off frequency. I have aligned CW,USB,SSB like in the manual: CW 9.000400 LSB 9.000000 USB 9.003000 Are these the correct setting
Hello the last few days had awful noise from the fan in the Centurion. Is there a good replacement for the original fan or should I just replace it with the original one? The replacement fan should b
Hello I would prefer the 500 HZ 6.3 MHZ, because the PBT is working on 6.3 Next would be 500 9 MHZ and next 250 9 MHZ I have all filters in my OMNI 6+ Cascading the 6.3 and 9 MHZ is a very big improv
Hello i noticed one strange thing with my OMNI 6+ on 80 meter cw. I key the tx for a log time, suddenlly there is a "ploppp" in the headphone and I monitor the power output on the external powermeter
Hello from Germany just got a used 1208 transverter 10/6. I have very high noise on 6 meter and also got a lot of TV/broardcast station around 50.085 up to 50.150 Other people close to my qth don&acu
Hello from Germany, I used an OMNI 6+ during the IARU fieldday. First wanted to supply the OMNI with a car batterie, buffered with a charger, but when the voltage went under 11.5 volt there was a chi
The jumper is located on the LOGIC Board just to the left of U7 and below R13. Snip the jumper and it transmitts from about 1.7MHz to 29.999Mhz. As to the AGC being too fast I agree. Change C46 on th
Hallo i noticed a much less sensitivity on 12 and 10 meter on the Paragon. All seemed o.k. up to 22 MC, but above there is much less sensitivity. Any help? 73 de Harry, DK2GZ
Hello Tom and the TenTec user group I am using TenTec 500 and 250 in both zf. Also the 1.8 at 6.3 Mhz(generally for rtty) I use the following setup: 500 HZ in 6.3 Mhz 20 meter and above 2 times 500 H
Hello for normal operation I use the rear keyer jack with the internal keyer. During contest I use the second key jack to key trx with the lpt1 form my computer. Everytime I run into the same problem
Hello the problem is solved now. When the VOX is switched on in CW mode, the try wont key. If the VOX is switched off in CW-mode all o.k. now. Have a nice weekend. 73 de Harry, DK2GZ