Hello I am using the PARAGON I with the CENTURION amp. Therefore I dont need the relay to key the amp. I found some advice in the 1999 archiv to shut off the relay in the Paragon by solder a bridge.
What I or we need in a new TenTec: RX-side: RX-antenna input for beverages on the low bands Crystal filters in the frontend DSP-filters as an addition to the crystal filters Second receiver, also usi
Hello just got my third TenTec now. It is an ARGONAUT II. Searching the web and the archive, I only found the AGC advice. Also at eham.net I found only one review about the ARGO II. Who is also using
Hello, is there any chance to hookup an amp, like a TenTec Centurion, at the ARGONAUT II. In the manual I only found a hookup description with a DELTA II, but the ARGONAUT II dont have any ACC-socket
Hello my second rig is a Paragon I, first one is an OMNI 6+. I noticed a strong filter blow by and TenTec told me the problem is the phase noise of the Paragon, I saw some posts about a phase noise m
--part1_12f.80771f7.2930e30e_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello, after 3 hours in the CQWW there was nomore full RX after TX. Thought the rela
--part1_7f.1b4dba64.28f19ca1_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello I have a external preselector here. How can I hook up an external preselector
--part1_8a.bfbb8ee.28c3f016_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello again, thanks again for all the replies of my last question. This is a fantasti
--part1_7e.1a37b604.28c53394_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello David, I am using an OMN6+ with an AL80A. Simpley connect the RCA relay plug w
--part1_6f.1a5b1aa7.28cb7407_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello just noticed a chip only on 15 meter and always when using split operation wit
--part1_bd.1340e764.28bea5de_boundary Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Hello beside my OMNI 6+ I got a PARAGON as a backup rig. Now I have two questions: F
I am looking for a pair of INRAD 2.8 filters for my OMNI 6. The filters need send to Germany ! 73 de Harry, DK2GZ -- FAQ on WWW: http://www.contesting.com/FAQ/tentec Submissions: tentec@contesting.co
Hello, think my cw offset adjustment doesn=B4t. Hooked up a second receiver and set the offset to 400 Hz and listen on the second rx, then set the offset 990Hz and listen again, the signal was still
Hello, thanks for all the replies in the last few days. Fixed the problem now by adjusting the C31 on the logic board. Did also some on air tests and the OMNI 6+ (no upgrade version) sounds like a re
Hello I am a little confused about the parts they had sent to me. I have got two little bags with the same items in, all two bags labeled with R38. Did I missed someting for the step 1 (reducing the
Hello, i am using a OMNI 6+ and think the cw keying sounds a little chirpy. The little chirp is on all bands, also using low power (abt 10 watt out).It is not the power supply! Checked the sound on a
Helle to all I have the same problem with my OMNI VI+. Als using a linear. The problem is also when the linear is in stand by mode. The problem is gone when the linear is totaly switched off. I using
Hello exactly the same situation on my side and I fighting against it for weeks now. OMNI 6+, Heil-headset, AMP on the side, but no computer control cable and remote knob. I think it is nor RF that p
Hello i am looking for someone who have experience with the inrad filters instead the original tentec filters. I think the original tentec filters not as sharp as they could be. I there anybody who u
Hi, i have to crystal filter in the 9MHz IF. One should be the model 217 the other the model 219. In the manual in i saw: model 217 500 Hz eight pole for cw model 219 250 Hz six pole for cw But i cou