This is why l love this reflector. There's always someone who's "Been there, done that" . Sent from AOL Mobile Mail There was a ham in DFW area well regarded on Kenwood repairs. Not sure he is still
Touché.... (I hope the reflector doesn't discombobulate the paragraph formatting) NRA Proposes Million Ham March Oldham, Connecticut - The NRA (National Radio Association) has proposed a march on
Thought so. The reflector made it almost impossible to read. Oh well... Touché.... (I hope the reflector doesn't discombobulate the paragraph formatting) NRA Proposes Million Ham March Oldham, Co
My cousin has the same sign hanging in his pub in Gatlinburg. Sent from AOL Mobile Mail <div id="AOLMsgPart_2_86ecc80e-e521-4e9f-9e13-5fa4ad592439"> <div class="aolReplacedBody"><div dir="ltr"> Lots
<div id="AOLMsgPart_2_37fe4b85-0d7e-4ad3-8a0d-e6cbbfc89433"> Hi Perry, Yeah, it was an April newsletter article I wrote a few years back. The reflector made it hard to read because it ran the paragra
Aha... Thanks Gus. Later, Joe, K8MP <div> Sent from AOL Mobile Mail No, it came through fine here via Comcast in Denver. I'm using Thunderbird for email. Gus Hansen KB0YH ____________________________
Steve/Gary, 10 & 12 share a pair of relays and 15 & 17 share a pair. So I agree with Gary, one failed relay would not cause you to lose 12 and 15. Here's a link to the manual if you need it. The Low
PS- Joe, K8MP Sent from AOL Mobile Mail <div id="AOLMsgPart_2_b813d809-0388-455e-a781-1e713c8d9003"> <div class="aolReplacedBody">Steve/Gary, 10 & 12 share a pair of relays and 15 & 17 share a pair.
Gents, Winmoor does not support the Omni 6 Plus in their Rig Control software. I'm thinking that someone once told me there was a different brand and model that used a command set equal to or very si
Thanks Rod. I'll check it out. Later, Joe, K8MP Sent from AOL Mobile Mail Joe, seems like I used Icom 735 (some older version like that) with my Paragon that has an N4PY chip. The Omni 6 may be the s
Thanks Carl! Sent from AOL Mobile Mail It uses the Icom interface. Just select an Icom radio at the correct baud rate. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 <a href="http://www.n4py.co
Thanks Greg, I keep muffin fans blowing on the rig's heat sink and power supply's heat sink most of the time already. Later, Joe, K8MP Sent from AOL Mobile Mail Subject: Re: [TenTec] Winlink and Winm
Jim, et al, They must have removed the 735 from the list. It only shows newer models of Icoms. They do have two generic Icoms in the list: "Icom Amateur radios" and "Icom Amateur Radios (Early)" I ch
I meant to ask if the Signal Link is a necessity with Winmor. I'm using the serial cable for rig control and that set up keys the rig fine when I'm running MMTTY and FLDigi Joe, K8MP I used the Icom
Oh contraire Carl. I've been keying it thru the serial port using MMTTY and FlDigi.for a long time. The Omni VI does not have a keying interface. You would need to use a Winkey keyer for that. Carl M
Thanks Greg. I tried it when there was no activity and even went "Off channel" to see if that made a difference. I keep thinking it is an operational error though because the rig did accept the QRG a
Gents, <div>I threw in the towel on making WinLink and Winmor work with my Omni VI Plus. I have WinLink working over our local Mesh network and I was hoping get it working on HF but no dice. Thank yo
They're talkin' Carl. The rig accepts the mode and QRG commands from the PC but apparently it doesn't accept the command to xmit. Sent from AOL Mobile Mail There's 3 things that have to match. Baud r
Hmmm... I run MMTTY and FLFigi on that same PC over the same connection and they key the Omni VI Plus fine. Those work but WinLink/Winmor does not, so it's gotta be something in the program or a sett