Could be I have been lucky but I have never had problems with my Ameritron AL-811. I run mine off an OMNI V. I use the tune key to tune the amp. I have had the amp for 8 years and bought it used. It
My OMNI V is having a problem. I turn it on and no receive on any band. I do get full RF output on all bands and the rig switches from transmit to receive and back but no audio. However, if I flip ri
After taking covers off and cleaning connectors on all boards radio was working fine. Left rig on for 6 hours and no problems. Stations coming in and strong with no distortion. On 80 meters was getti
No problem with that Joe. This is a brain buster. Can't get it to stay dead to trace it. Dan/N4VET **It's only a deal if it's where you want to go. Find your travel deal here. (http://information.tra
Further investigation reveals these symptoms. 1)Turn rig on all is fine. 2)After about 15 minutes signals drop out nothing is heard and SWR is way up on transmit. 3)Turn rig off for about 20 minutes
Well, I called Ten Tec this morning. I told them of this problem I am having with my OMNI V. Was told that the problem sounded like a synthesizer problem. I told them that it did not seem to me that
My OMNI V is now working again. The problem was discovered when I put my frequency counter on the rig and narrowed the problem down. Even though the rig showed a frequency of 3.945 my counter it was
I was at the point that hitting the radio with a hammer would have not been a bad idea, but I just reflowed solder Jim Hi Hi. 73, Dan/N4VET **It's only a deal if it's where you want to go. Find your
Steve, would this method work the same for the OMNI V? I am putting together a sort of service manual for mine and if it is the same I will place it in the manual. Dan/N4VET **Psssst...Have you heard
Ernie, when you get the reply from Paul could you share the procedure with us or with me. Also, I have noticed that emails with Ten ten tend not to get a reply you may want to call and have them send
Picked up a 263G VFO for my Corsair II today. It came without a manual. Would like to try it out tonight and need to know connect it to the rig. The Molex connector is easy but it also has two RCA pl
Thanks Steve. That is what I was going by too. I just don't want to blow anything. Could you help out with function controls? What is the scale on the brown glass for? What does the AB knob do? What
Thanks Jim. Could you give me info on function controls and scale on the brown glass? Thanks, Dan/N4VET **One site keeps you connected to all your email: AOL Mail, Gmail, and Yahoo Mail. Try it now.
Thank you Phil. I think I will like it. Santa came early for me here. 73, Dan/N4VET **One site keeps you connected to all your email: AOL Mail, Gmail, and Yahoo Mail. Try it now. (http://www.aol.com/
I now have all the information I need. Thank you all very much for the help. You are a great bunch of guys. 73 and a Merry Christmas to all. Dan/N4VET **One site keeps you connected to all your email
Have an OMNI V. Had the coax off the rig and was getting an S6 meter reading. If I go from the 2.4 to the 1.8 SSB filter goes to 0. On the 2.4 filter if I turn PBT to the right meter drops to 0 if I
**Join ChristianMingle.comŽ FREE! Meet Christian Singles in your area. Start now! (http://pr.atwola.com/promoclk/100126575x1221246370x1201421635/aol?redir=http://www.christianmingle.com/campaign.html
With no antenna connected is it normal for the PBT control to cause the S meter to go from 0 db to about a 6 db by turning the PBT control off center? All seems normal with OMNI V rig but this does n
I have worked on this board before but did not keep notes but for how I fixed it 6 years ago. I know it is on the bottom of the OMNI V and I think I recall it to be under Xtal Filter board. Did I rec
Doug, remove the display and DeOx the pins on each side with a Q-tip. Do not spray the solution directly on the pins. After cleaning the pins with the solution replace the display board. That should