Is your Sony a plasma or an LED? 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com Rick, you may have got mine! I had purchased a similar model from Panasonic and tried everything to reduce t
Dave, What "normal/reverse" are you describing? 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com Hi, Folks I have had very good success running the Orion II on rtty. I use a Rigblaster pro t
Ah, yes, and the Orion is upside down from what I think it should be. Thanks - now I know what you're talking about. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com FSK TX Date can be selec
That's what my Orion I did when I ran the 1.x firmware also. Doesn't do that with 2.x. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com When I key my Orion 1 (v. 1.373b5) the red LED at firs
Be sure to send a note to Ditsnbits@tentec.com to report it. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com Have had my O2 only two months and I noticed the same thing when using the BinRx
I would guess it would be the same address - ditsnbits@tentec.com 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bou
You really don't think they single-sourced a critical part of any defense systems, do you? 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com --Original Message-- From: tentec-bounces@contesti
Except most routers are set for "0" in the third octet. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@conte
Agreed, but the radio is most likely getting assigned an IP via DHCP in the router, and most folks don't change the default settings. Then again, maybe I'm way off on this - I don't have an Omni VII
I'm trying to think of a modern Ten-Tec radio that doesn't use a relay for T/R switching, and can't think of one! 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com --Original Message-- From:
The Omni VI/VI+ used a reed relay for T/R switching, even tho they may have used diodes in the circuit. Remember all the complaints about how some folks could hear their relay and others couldn't? :-
Merle, I've been struggling with the "overdriven" audio sound ever since installing 2.062a. I also hope they get to this soon. The only solution I've found is to run both the NB and NR at between 1 a
There were a couple others of us who suggested this same thing. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com It may go against ham culture, but I suggested (long ago) that TT should sell
I don't think we were talking about open-sourcing. This comes up every now and again. I don't believe TT will go for that as they believe they have considerable intellectual property tied up in it an
I can do the same with only the ground side of the antenna connected at the 238B antenna tuner. The Orion has a lot of gain, and often I can copy signals with nothing connected to the antenna port at
John, My Orion 1 exhibits what you describe - I have nothing connected to Ant 2, but if I switch from Ant 1 with a signal on it to Ant 2, I can still hear the signal, though faintly, from the Ant 1 i
That's how my Orion 1 works - S9 on Ant1 can just be heard with no S-meter movement with Ant 2 selected. 73, Duane Duane Calvin, AC5AA Austin, Texas www.ac5aa.com --Original Message-- From: tentec-bo
Don't completely throw away the paper - I use a scratch pad to write notes I want to remember on my next transmission (his name, QTH, etc.) But head copy is wonderful - I run mobile CW when I take lo