Hi all I really enjoyed using a friends argonaut and decided to buy a new TenTec. I'm getting used to an Eagle. It's my first "new" radio since purchasing a SB101 over 40 years ago. After ordering th
Hi all... Wanted: I am looking for an enclosure for my hamfest found 'basket case' Orion 565. There may be some missing internal sheet metal as well. It looks like there is supposed to be some sort o
Works fine. Not modified. :Looks good. Radio, wall wart, and telescopic antenna only. Manuals and control software at Ten Tec web site. Sparkfun Electronics had a nice USB to RS232 adapter. If unfami
I just sold.my RX320 to Phil McGinnis 216 Charlestowne Dr Madison MS 39110. I know he would be happy to have an original manual. _______________________________________________ TenTec mailing list Te
Thanks and apologies for copying the entire digest. I'm still getting used to gmail on the cell phone. 73, Bob _______________________________________________ TenTec mailing list TenTec@contesting.co
Has anyone done this? I've been playing with my new Eagle and am considering the addition of an Afedri board, http://www.afedri-sdr.com, to use with the PeeCee and SDR software for a panaromic displa
I would use this for the buffering of the 9MHz if output: http://www.cliftonlaboratories.com/z10000_buffer_amp.htm 73, Barry N1EU Barry Thanks. It looks like it will do the trick if I can either relo
If anyone has or gets wind of an unrepairable 565 or 566, I can use the enclosure snd some of the mon electrical bits inside. This to complete the hamfest basket case 565. Thanks! 73, Bob ah7i/w4 ___
Rodney Hey! Thanks. How did you end up with just the top? Is it the same as the bottom, minus the feet? Do you know where the bottom is? I'll try to post a photo of what I have sometime tomorrow afte
I'm still getting used to this new Eagle and there's something not right. About 2 hours into extended CW QSO the noise floor came up. At first I thought is was local. S5-S7 making copy difficult. I d
It's got the horsepower but the sun roof leaks, the limited slip isn't as good and I heard that Franklin twisted the rear springs at the track when he put on some sticky tires and gave it a NOx shot.
If you recall, I had S5 noise, uniform, all bands, on the Eagle with either the dummy load or nothing connected at the antenna port. Ditto with alternative power supply. So bad I had to cut a QSO sho
I enquired about purchasing an Eagle enclosure to use for accessories. They don't sell it without the radio. It would be nice to have same size, matching, enclosure to add a power supply, SBC, displa
Ten Tec manual says Aux 1 connector is a 9MHz IF tap, 50 Ohm. "Starting with Serial Number 305136000O, the Rear Panel of the Eagle shows AUX 1 and AUX 2. AUX 1 is pre-installed upon shipment of the t
Eric I've carefully gone over the schematics and can not find the tap. They are dated 2010 and I can not find any revision notes either. I will really appreciate it if you can tell me where the 9MHz
I receive the list in digest mode so this may be a little disjointed. *What to do depends on where it is in the circuit. I want to learn and then move if necessary. My thinking is to add a panadapter
Here you will find a description of the second receiver/pan-adapter I am thinking of adding to the Eagle. http://www.afedri-sdr.com select the "net-sdr". It has 80MHz sample rate and 12 bit. Maximum
I assembled a nice piece of well shielded RG58 with 2 RCA plugs to replace the "audio" cable I was using between the SW RX and the 9MHz tap. With the audio cable it was as I had an antenna connected
Watch the whole band at once to see what's up. Say you get up in the AM and wonder what's up on 10m look at pan and you'll see those two signals without tuning the whole band. Contest. See the weak g
Does anyone have up to date schematic showing tap.? _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec